r/overclocking • • 11h ago

Intel Nova Lake leaks

Thumbnail
gallery
64 Upvotes

the bLLC variant , on a z990

*intel extreme profile ( iccmax 380a )

unlocked power full avx2 load ( vrm p-out 320w )

-

8x P-core 5100mhz * 5200mhz only when 2 cores r active ( separate vcore didcated to the p-core )

16x E-core 4600mhz ( separate vcore didcated to the e-core )

4x LP E-core 2200mhz ( VCCSA )

ring 4500mhz ( separate vcore didcated to the ring )

L3 cache size 144mb

D2D 3000mhz ( VNNAON )

NGU 3000mhz ( VCCSA )

tjmax 100c stock ,, configurable up to 110c on z990 * not recommended

-

DLVR is still part of the chip ,,, because of the hotspots and the nature of the 2nm size of the compute die

*we gonna have 4 separate voltage rails from the vrm to the compute die instade of a single vcore

one for each , ring , pcore, ecore , *to lower the hot spot issue.

it was suggested ,but many of the motherboard manufacturer (asus one of them) weren't happy with it ,,, because it will increase the cost and the complexity of the motherboards.

,it is still not confirmed yet,

dlvr outputs voltages

p-core at 1.150v

E-core at 0.950v

ring at 1.200v

-

cinebench r23 score is at 42000

cinebench r26 score is at 10000

-

the p core ratio will drops to 5100mhz under full avx2 load

no avx512 support the small traces cant handle it.

4x LP E-core will lower the idle wattage to 20w from 40w at idle. browsing will be at 50w

*with the unlocked power and it has it's own saprate cache,,,

disabling it along side the c state will only improve the latency

what is the bottlenecks on this gen for the bLLC ?

pcore + ecore + ring hotspots and thermal limitations / NGU / IMC and the gear 2

D2D can support up to 3900mhz so not really.

gaming performance is good ... equal to amd x3d.

the none bLLC variant is good but will be copy and paste from the arrow lake flagship variant with a slightly better cache.

and slightly better hotspots distribution *only if they separated the vcore rails.

it also will have a higher cinebench r23 score *at 45000

another note : the broken avx offset finally got replaced with somthing similar to amd pbo.

they called it FVB "frequency velocity boost".

each voltage rail of these will have a separate load line... p core / e core / ring / vccsa

with an optional sagment 2 load line for the pcore only good for high pcore ratios stability when gaming

unofficial dlvr bypass mode is still available like the arrow lake ... but not recommended ... without dlvr the hot spots r not manageable

igpu ... they added only 2 more cores to the same igpu tile found on the arrow lake.

*all of these r from an internal trusted source who works for intel.


r/overclocking • • 37m ago

X3D2 @ 8600 2200 CL32 GDM disabled bench profile and live YouTube Karhu run

Thumbnail
gallery
2 Upvotes

For any one who thinks you need some kind of special settings to run a certain MT/s

No !! You need an extremely lucky purchase or bin chips like I have, over time you’ll eventually find one that runs high memory speeds, this chip boots 6800 in 1-1 mode and runs 6600 with only 1.26Vsoc, can also Bclk up to 6633-2211 using 1.3Vsoc

8500 GDM disable just runs at low VDDP and Vsoc
8600 GDM enabled runs also really well, but GDM disabled requires lower ambient temps, and why it’s just a BENCH profile, with some stability 😊

When my temps are low enough to run 8600 GDM disabled, I can also run 8700-2200CL32 GDM enabled at the same voltages other than Trcd being 48

I’ll post some pics as well as a link to a live unedited run from 4900% up to 5000% then reboot to bios to show settings.

Link to a unlisted YouTube video, please leave a comment but also remember I’m AIO, low ambient temps and just a
Pc case not a bench table, this is my daily PC on my desk

As you’ll see, no special settings at all !!!


r/overclocking • • 1h ago

Help Request - CPU Looking for a direct die for my Ryzen 7 9850X3D

2 Upvotes

Hi everyone!

I'm looking for a direct-die waterblock for my Ryzen 7 9850X3D.

I've spent quite a bit of time trying to find a Thermal Grizzly Mycro Direct-Die PRO, but it's been absolutely impossible to find one in stock anywhere! 😅

I'm based in France, so ideally I'd like to find a European retailer.

Does anyone know where I could get one, or recommend an alternative with similar or better cooling performance?

I've also come across the Supercool Ryzen G9 direct-die waterblock, but I'm not entirely comfortable ordering from their website, and I'm a bit worried about the potential customs duties, VAT, and import fees.

Thanks in advance for your help!


r/overclocking • • 2h ago

Help Request - GPU ROG Strix RTX 4090 – Thermal Grizzly PTM Pro and Arctic PX-1 vs Putty Pro

2 Upvotes

Hi everyone,
I’m planning to replace the thermal paste and thermal pads on my ASUS ROG Strix RTX 4090 and would appreciate some advice.
For the GPU die, I’m considering the new Thermal Grizzly PhaseSheet PTM Pro instead of traditional thermal paste. Has anyone tried it yet?

My main concern, however, is the thermal pads.
From what I’ve found online, ASUS uses some unusual thicknesses on this card (around 1.25 mm and 1.75 mm), so I’d prefer using thermal putty.
I’m currently deciding between Thermal Grizzly Putty Pro and the new Arctic PX-1.

The PX-1 looks particularly interesting because it comes in preformed 1.5 mm sheets that can be cut to size and potentially stacked to accommodate different gaps. It’s also considerably cheaper, with around 78 g of material in one package, whereas I’d need to spend significantly more on Putty Pro for a complete replacement.
Would Arctic PX-1 be a good alternative to Putty Pro in terms of thermal performance, compressibility, and long-term reliability? Would stacking the sheets cause any issues with heatsink contact?

I’d appreciate any feedback, especially from anyone who has worked on a Strix RTX 4090.
Thanks!


r/overclocking • • 2m ago

Tightening RAM timings

1 Upvotes

This is my first ever time trying to overclock RAM. I have successfully increased memory speed from 6400 to 7200 M/T without changing any timings. Done OCCT 24 hours tests which came back successful with zero errors.

I am trying to tighten RAM timings to reduce latency, how far can I go to improve gaming performance.


r/overclocking • • 4h ago

Help me get the stable overclock on my Ryzen 5 5600X

2 Upvotes

I’d like to get the maximum stable performance out of my Ryzen 5 5600X, mainly for gaming.

My specs:

  • CPU: Ryzen 5 5600X
  • Motherboard: Gigabyte B550M DS3H
  • Cooler: Cryogen H7 tower cooler

Could someone help me find the best BIOS settings for maximum performance while keeping temperatures and voltages safe?

I’m especially interested in PBO2, Curve Optimizer, PPT/TDC/EDC limits, and Boost Override.

I’d really appreciate some recommended values or a step-by-step guide to achieve the highest stable overclock possible.

Thanks!


r/overclocking • • 1h ago

Help Request - RAM RAM Overclocking advice

1 Upvotes

For reference, this is my first time really closely looking into overclocking so please go easy on me!

So I've been looking at a minor upgrade to my PC, (12700k to a 14700k). In light of that, I'd been checking back on my RAM specs and note I have 5600 MT/s, 32gb DDR5

When considering the upgrade I started looking at the possibility of pushing the RAM to 6000 MT/s, so I tried it, pushed voltage to 1.35, increased clock to 6000 and ran a stress test for an hour, maxxing out at about 56-58c.

So on paper that seems okay, but after running 3D Mark, while the rating increased by about 300, I'm wondering if this is actually worthwhile, will it hold up and stay safe or am I straining it more than I necessarily need to? Will it work in my favour when the 14700k is installed?

I know these are quite vague questions but was just hoping y'all with a lot more experience might be able to give me a bit of advice and what else I should be looking out for, as was unsure if it would have an affect when the new CPU is installed.

(Thank you again)


r/overclocking • • 1h ago

My custom loop now has its own monitoring dashboard — coolant, flow and pump speed on a TURZX panelI've been refining this build since 2020, and recently built **CORE LABS Studio** to bring its cooling and PC telemetry onto the TURZX 9.2-inch display.

Thumbnail
gallery
1 Upvotes
The demo is my real system: a 5900X on a custom CPU loop, an air-cooled 7900 XTX, and Aqua Computer High Flow NEXT. Coolant temperature, flow and pump speed sit alongside CPU/GPU data instead of being scattered across views.
It's a portable, offline Windows app with themed layouts and workload profiles including ECO and DEEP SLEEP. Supported readings depend on the sensors installed; this is monitoring, not a promise of automatic pump or fan control.
Disclosure: I develop it. There are FREE and paid PRO tiers; PRO purchases are expected on **23 November**, pending Stripe identity verification.
For your loop, which deserves the most screen space: coolant temperature, water-to-air delta or flow?

r/overclocking • • 4h ago

Update on #1 Attemp in Time Spy with NVIDIA GeForce RTX 5070 Ti(1x) and AMD Ryzen 7 9800X3D in my daily system on pure Air and with no mods.

1 Upvotes

Last night we were able to go from #6 to #3 in the world, but as expected as we got closer to the top we started to run into stability issues. Im pretty sure we can get to first place as once again i screwd up many runs. Tonight we go again and will be live on https://www.twitch.tv/a_diretoria


r/overclocking • • 6h ago

Help Request - RAM Crucial Pro OC 32GB DDR5 6400MHz CL32 to 6000MHz CL30 With a 7800X3D

1 Upvotes

Hey, everyone - just making this post to ask for some assistance with my RAM speeds on my 7800X3D. I know that running 6400MHz CL32 on a 7800X3D is generally quite unstable and will usually result in the memory controller going into 2:1 mode, so as a result I've been running my Crucial RAM with the EXPO II profile of 6000MHz CL36-38-38-44 to circumvent this. However, I was wondering if I could potentially get more out of this RAM by downclocking to CL30 from this EXPO profile but am unsure as to how to do it. I've seen that Micron dies are more difficult to tighten that Samsung and Hynix dies, but I'd like some insight into if it's possible. For example, what subtimings and voltage would I set? Should I start from the 6000 CL36 profile and tighten from there or the 6400MHz CL32 profile and downclock that? I've never done any manual tuning with RAM before so any help would be greatly appreciated. Thanks, guys!


r/overclocking • • 7h ago

5585 Core Effective 13700k Cinebench r23 10 minute OC (e-cores off)

1 Upvotes

Vids are kind of high though it just sits at 5.6 all core sitting at idle with 1.423 VID max in the desktop no apps open. I got it to run 5700 all core in heavy threaded UE5 games but vids were sitting at like 1,483 for too long I think. Is this thing gonna fry itself like this?


r/overclocking • • 7h ago

Overclocking rx 5700xt red devil

1 Upvotes

i have te red devil and i would want to overclock it for better gaming performance but i can only achieve like 2100mhz at 1.2 voltage if i unlock the voltage what would be the max safe voltage for daily driving that will not destroy the silicon


r/overclocking • • 1d ago

250kf rtx 5080 , 6000cl36 vs 8200cl38

Post image
30 Upvotes

Bf6 1080p, low TAA , Mirak rush.


r/overclocking • • 3h ago

Help Request - RAM who else hates teamgroup

0 Upvotes

the worst part? they laser-etch their own stuff to their chips(uhh i was too lazy to take pic of it)
and what the hell is this info: Module Part Number: UD5-5600

like not useful at all
i just want to know if its a or m die


r/overclocking • • 19h ago

Need help with “cpu fused boost clock limit” 9850X3D

Post image
6 Upvotes

Hello people!
I have never heard about anything like this.
It seems that my cpu is locked zo 5.65 ghz?
I noticed because not even on single core benchmarks did it exceed that value while giving it +100mhz with -20 all core pbo.
If this cannor be changed , is there a reason to still put 100 mhz plus on it? I guess not?
And is there any benefits from pbo like this?


r/overclocking • • 17h ago

is undervolting a 13600KF on a Gigabyte B760M Gaming X DDR4 Gen 5 basically impossible without triggering CEP?

3 Upvotes

Hey everyone,

trying to undervolt my i5-13600KF on a Gigabyte B760M Gaming X DDR4 Gen 5 (latest BIOS) and I'm hitting a brick wall with IA CEP

at stock (Intel Default / 181W limits), I get around 22,868 in Cinebench R23, pulling ~158W at 79°C max. wanted to drop temps/power a bit and push the score closer to 24k, so I went into BIOS and tried the usual stuff:

Switched Select MCU to Rev 0x104 and set PerfDrive to Spec Enhance,

Tried setting a negative Internal CPU Vcore Offset (-0.080V) in Adaptive mode - completely ignored, VID stayed around 1.27V,

Tried Dynamic Vcore (DVID) at -0.080V - barely did anything, temps stayed around 77°C

Tried lowering IA AC Loadline directly (tested 30 and 55, default auto was 70). Voltage dropped, but CEP immediately kicked in and tanked my R23 multi-core score down to ~19,200–20,800

Looked everywhere in Advanced CPU Settings / Internal VR Control and there's no option to disable IA CEP at all (assuming Intel locked it out for 13th gen on B760) Has anyone managed to actually undervolt a 13600K/KF on this specific board (or similar Gigabyte B760 boards) without CEP clock stretching killing performance? Or am I stuck just running stock / finding the exact AC Loadline floor right above where CEP triggers?


r/overclocking • • 12h ago

Help with ram timings

1 Upvotes

Hey all a little new to optimizing ram timings. Kit I have is Crucial Pro 2x16GB 6400MT 32 40 40. I'm actually running expo 2 at the moment which is 6000 36 38 38 because it can run 1:1 UCLK stable (obviously). I've tried tweaking my expo 1 to be at least be 1:1 but within 20 minutes of an OCCT memory benchmark, errors occur. Been seeing some really cool tweaks in this subreddit and in awe how low and stable some people can get their latency to be. Just wondering if anyone with the same kit has had success optimizing theirs to be fast/stable or some words of advice or if I'm unlucky. CPU is 9800x3d motherboard is MSI Pro B850P Wifi


r/overclocking • • 23h ago

Any RAM timings worth tightening or adjusting further?

Post image
7 Upvotes

This is my first time manually tuning RAM timings, so I'd really appreciate some feedback from more experienced overclockers.

Are there any timings I could tighten further, or anything else you'd recommend adjusting based on my ZenTimings screenshot?

So far, I've run TestMem5 for 6 hours and y-cruncher for another 6 hours, with no errors in either test.

Any advice or suggestions would be greatly appreciated. Thanks in advance!


r/overclocking • • 15h ago

RTX 3070 (Gigabyte OC Vision) undervolt, 1800MHz @ 950mV, stable in every game I've tried and runs way cooler

1 Upvotes

My Gigabyte RTX 3070 OC Vision was hitting 90°C+ in games so I finally sat down and undervolted it with MSI Afterburner. this is the most stable setup I've found so far, no crashes in any game I've tried.

temps now:

  • AAA games: around 69-70°C
  • heavy modded games: around 75°C
  • before: 90°C+

settings:

  • Core voltage: +0
  • Power limit: 100
  • Temp limit: 83
  • Memory clock: +1000 (shows 8000 MHz in AB)
  • Curve: flattened at 1800 MHz @ 950mV, everything after 950mV is locked at the same clock so it never goes above that voltage

to do the curve, open the curve editor (Ctrl+F), find the 950mV point and drag it up to 1800, then hit apply so everything past it flattens out.

driver is 621.24.

every chip is different so if yours crashes, try dropping the clock a bit or bumping the voltage up to 962/975mV. curious what other 3070 owners are running, drop yours below.


r/overclocking • • 1d ago

Aimed for Top 100 in Time Spy on air, somehow hit #18 in the world w/ 9800X3D + 5070 Ti

8 Upvotes

My goal was just to crack Top 100 on a completely stock, air-cooled daily rig—no shunt mods, no XOC BIOS, no crazy cooling, just pure BIOS, RAM, and GPU curve/fabric tuning.

Ended up blowing straight past Top 100, into the Top 20, and now I'm sitting at #18 overall. The wildest part is I still messed up a bunch of runs along the way and definitely haven't hit the ceiling yet.

I'm going for Top 5 or Top 3 tonight. and will be streaming live.


r/overclocking • • 19h ago

Gigabyte AORUS RTX 5080 MASTER – Up to 30°C GPU Hotspot Delta! Is This Normal, a Cooling Defect, or Should I RMA?

Thumbnail
gallery
1 Upvotes

Gigabyte AORUS RTX 5080 MASTER – Up to 30°C GPU Hotspot Delta! Is This Normal, a Cooling Defect, or Should I RMA?

Gigabyte AORUS RTX 5080 MASTER – Up to 30°C GPU Hotspot Delta! Is This Normal, a Cooling Defect, or Should I RMA?

Hi everyone,

I built a new gaming PC back in September with the following specifications:

  • CPU: AMD Ryzen 9 9950X3D
  • RAM: 64GB DDR5 6000MHz CL30
  • GPU: Gigabyte AORUS GeForce RTX 5080 MASTER 16GB
  • Resolution: 2560 × 1440 (1440p)

I spent quite a bit of time researching different RTX 5080 models before purchasing this card. I specifically chose the AORUS MASTER because of its premium cooling design and generally positive thermal reviews.

I've been using the card for approximately two months, and until recently, I was completely satisfied with it.

I haven't noticed any significant performance issues, FPS drops, crashes, or instability.

Even in demanding games at 1440p with maximum graphics settings and ray tracing/path tracing enabled, my GPU core temperature generally stays around 60–65°C.

However, while running some benchmark tests out of curiosity, I discovered something that has me quite concerned.

The Problem: A 26–30°C GPU Hotspot Delta

After researching other owners' results, I found several reports of the same RTX 5080 MASTER running with GPU-to-hotspot temperature differences of approximately 8–15°C.

My card, however, behaves very differently depending on the workload.

In certain stress tests, the GPU core temperature stays around 60–67°C, while the GPU hotspot reaches 90–94°C.

This results in a 26–30°C temperature delta between the GPU core and hotspot sensors.

My Test Results

All tests were performed at an ambient room temperature of approximately 23–25°C.

TestGPU TempGPU HotspotDelta
FurMark (10-minute mark)57°C70°C13°C
AIDA64 GPU Stress Test62.6°C92.2°C29.6°C
OCCT (5-minute mark)67.4°C93.6°C26.2°C
Marvel's Spider-Man 2 (1440p, RT, Ultra)60–62°C78–87°C18–25°C
GTA V Enhanced (1440p, RT, Ultra)60–62°C78–87°C18–25°C

During 3DMark testing, the hotspot also reaches approximately 91°C and can remain at that temperature under sustained load.

What concerns me most is the inconsistency between workloads.

For example:

  • FurMark: Only a 13°C delta.
  • AIDA64: Almost a 30°C delta.
  • OCCT: More than a 26°C delta.
  • Demanding games: Often an 18–25°C delta.

I understand that different workloads can produce different temperature distributions across the GPU die.

However, I'm unsure whether this level of variation is expected for this particular card.

Case Cooling and Airflow

I believe my system has excellent airflow.

My cooling configuration includes:

  • 3 bottom intake fans
  • 3 front intake fans
  • 1 rear exhaust fan
  • A top-mounted 420mm AIO radiator with fans
  • All 3 original GPU fans
  • The additional fan included with the AORUS MASTER, installed above the graphics card

All GPU fans are working properly.

The fact that my GPU core and VRAM temperatures generally remain around 60–65°C also suggests that overall cooling performance is quite good.

Troubleshooting I've Already Tried

To rule out software or firmware-related problems, I've tried the following:

  1. Updated the GPU VBIOS.
  2. Tested different NVIDIA driver versions.
  3. Switched to the GPU's secondary BIOS.
  4. Ran multiple benchmark and stress-testing applications.
  5. Cross-checked temperature readings using different GPU monitoring programs, including MSI Afterburner.

Unfortunately, the hotspot behavior remains similar.

I haven't opened the graphics card or removed the heatsink because I don't want to risk my warranty or disturb the factory-applied thermal interface material.

What Could Be Causing This?

My main suspicions are:

  • Uneven contact between the GPU die and heatsink/vapor chamber.
  • Uneven application or distribution of the factory composite metal thermal grease.
  • Incorrect mounting pressure or another heatsink assembly issue.
  • Less likely, a temperature sensor or monitoring software issue.

These are only possibilities, not confirmed diagnoses.

My Biggest Concern: Summer Temperatures and Long-Term Reliability

The ambient temperature during all my testing was only 23–25°C.

During summer, the temperature in my room can become considerably higher.

If the GPU hotspot is already reaching 90–94°C under current conditions, I'm worried about how the card will behave during hotter months.

I also wonder whether a consistently large hotspot delta could affect the card's long-term reliability, even if gaming performance currently appears normal.

Questions for RTX 5080 Owners and Hardware Experts

I'd really appreciate some advice from people who own this specific GPU or have experience with GPU cooling systems.

  1. Is a 26–30°C hotspot delta normal for the Gigabyte AORUS RTX 5080 MASTER?
  2. If you own the same model, what GPU core, VRAM, and hotspot temperatures do you see in OCCT, AIDA64, 3DMark, and demanding games?
  3. Why would FurMark produce only a 13°C delta while AIDA64 and OCCT produce almost 30°C?
  4. Could this indicate poor heatsink contact, uneven mounting pressure, or an issue with the factory thermal interface material?
  5. Could this temperature difference cause long-term reliability problems even without noticeable thermal throttling?
  6. Since the card is relatively new and still under warranty, should I contact Gigabyte for an RMA or request a replacement from the retailer?
  7. Are there any additional diagnostic tests I can perform without disassembling the card?

Just to clarify: My GPU performs well in games, and I haven't experienced crashes or obvious performance degradation. My concern is the unusually large hotspot delta compared with results I've seen from other owners of the same model.

I really don't want to send a relatively new, expensive graphics card in for warranty service unnecessarily, especially when I'm otherwise happy with it.

But at the same time, I don't want to ignore a potential manufacturing or cooling issue that might become worse over time.

I've attached screenshots of my benchmark and temperature monitoring results.

If anyone with the same AORUS RTX 5080 MASTER could share their own hotspot temperatures and deltas, that would be extremely helpful.

Thanks in advance for any advice or suggestions!


r/overclocking • • 14h ago

Pea-sized blob results in poor thermal paste coverage

Post image
0 Upvotes

My AIO performance was not doing so well for my i9-12900K, so I went to repaste and reseat the cooler, but noticed that the top and bottom of the IHS are basically paste-free. Seems like this would definitely cause poor overall contact with the IHS.

When I apply paste I always use a decent sized blob in the middle (perhaps too much, but that’s the better side to err on than too little). I expected that it would spread everything out evenly, but as you can see it did not.

What method do you use to apply paste with actually even coverage? Spread manually?


r/overclocking • • 14h ago

Trying to find a program that auto-tunes MSI Afterburner for a better power curve

0 Upvotes

A few months back someone posted some tool that hooks into MSI Afterburner to adjust power draw. I think the point was that normal 100% power draw from your GPU is not needed and this was better performance and cost savings. The software required Afterburner and it ran some automated hooks after install.

I have now completely forgotten what that was and can't find a trace of it on my PC. But I have recently installed Win11 and wanted to get it reinstalled. Anyone familiar with what I may be talking about?

Thanks!


r/overclocking • • 1d ago

Help Request - CPU 9950x3d after the latest Windows update, the temperature in idle mode increased.

Thumbnail
gallery
3 Upvotes

Hello everyone.

Previously, the temperature of my 9950x3d in idle was ~52-55 degrees (HYDROSHIFT II LCD-C + Lian Li TL + noctua nt-h2)

Presumably, after the KB5132061 update (but I don’t know exactly when), the temperature reaches 60–61 degrees after 10–15 minutes of inactivity and doesn’t drop. At the same time, the temperature remains the same when playing games.

(I also noticed that stuttering sometimes appears in the game that wasn’t there before (but it might have appeared with the game update). I also have the feeling that the computer itself is running slower and stuttering, even though the CPU isn’t under load.

I checked, the KB5132061 update installed normally, it’s not looping. The settings in the BIOS haven’t been changed. The mode is balanced. I’ve attached the remaining screenshots.