r/reloading • • 4h ago

I have a question and I read the FAQ Thoughts on my annealing

Post image
3 Upvotes

Hello I recently got into annealing. Just want to hear your advice/ opinion if it good or what to improve


r/reloading • • 4h ago

Something Unique(Vintage/wildcat/etc) 11x60mmR Mauser testing

Thumbnail
gallery
9 Upvotes

Prussian capture chassepot in 11x60mmR
Using 350gr .458” projectiles sized down to .447” (over several steps!).
14.5gr trail boss gives 1100fps, very accurate for what it is imo, mild report, minimal recoil.
17gr trail boss gives 1230fps, seemed a little less accurate but still good, recoil became a bit sharp even with just the modest increase in velocity.


r/reloading • • 5h ago

Newbie Rebates.

1 Upvotes

Don’t forget Hornady has a rebate running until 12/31/26. Does any other company have a rebate running?


r/reloading • • 6h ago

Load Development Alliant 2400 in 12 gauge, published data. For when Blue Dot’s fireballs aren’t quite big enough for ya!

Post image
3 Upvotes

r/reloading • • 7h ago

Newbie Max col?

Post image
5 Upvotes

Just did my first 50 rounds of 308 with HD 168gr BTHP and used varget and it’s a little late at this point and I was measuring my col and had some variation
I needed 2.810” but I’m over and under on some by 1 thousands is there some grace I was trying to make some match grade loads but first time loading


r/reloading • • 8h ago

i Have a Whoopsie I’m an idiot: Don’t cross-contaminate your powder!

Thumbnail
gallery
110 Upvotes

I’m an absolute idiot, and I’m posting this as a PSA about complacency and hubris in the hope others might learn from my idiocy.

After 36 years of reloading I finally managed to do what we all know not to do from day one, and that is accidentally cross-contaminate reloading powder. The result of my stupidity were .223 rifle rounds loaded with rifle powder contaminated with enough pistol powder to cause catastrophic failure (pics attached).

I disassembled the remaining ammo batch, and after weighing each load and pouring the powder into ice-cube trays, I see I’ve got significant traces of pistol HS-6 powder within the intended Winchester 748 rifle  loads. 

In the picture, you can see this in highlighted tray-slot #7 (HS-6 has larger and more silvery flakes than W748). 

Looking at my reloading log book, I’m thinking what I did was not properly clear out the powder hopper when switching from reloading pistol rounds to rifle.  Once again, completely my fault.

Now we know the cause, what were the results of this dumb-assery? I was on the bench sighting in the scope on my competition AR; a RightToBear Builder’s Grade 16” mid-length upper on a DSA lower. About 15 rounds of slow-fire into the session, a monumental “boom” instead of the expected “bang” occurs. I’m not hurt at all, but the magazine base is blown out and the upper receiver and bolt are ruptured. Looking at the bolt, it’s absolutely split and peeling like a banana. The results are the rifle in the top of one of the photos. 

Now, here is where my damn hubris bites me even more in the butt. You might think I’d tell myself  “Huh - there must be something wrong with my ammo, so I’d better stop shooting!” but you would be wrong. 

With a series of competition events looming and dwindling time to sight in, I stupidly tell myself “The fault can only be with the rifle, and not my precision-loaded, boutique custom reloads!”. With this sense of self-righteousness I pull out my second AR and start sighting that in for use in the competitions using the same batch of reloads.

Another ten rounds in, and “Boom” - the exact same thing happens to my Bushmaster. The Bushmaster did not hold up quite as well as the RightToBear; the photo (rifle on the bottom) shows a lot more destruction to the upper and bolt. 

Once again, I incredibly escaped any injury.

In hindsight, although I blew out two uppers I consider myself lucky in that I was able to identify the problem and implement a solution without injuring myself or anyone else. 

Interestingly, while I was sure there would be no warranty available due to the use of wildly inappropriate reloaded ammo, I reached out to the customer service team at RightToBear and explained my Tomfoolery. They (rightly) confirmed the warranty could not cover that damage, but incredibly they gave me store credit of a sum way higher than I could ever have expected or deserved. They seemed genuinely glad I was OK, and were very generous despite me completely causing the issue. I’ve since bought a replacement Builder’s Grade upper and already have it configured on the same DSA lower (both lowers seem untouched and work fine). A big kudos to the RightToBear customer service team! 

So, lessons learned:

  1. No matter how experienced one might be at reloading, it’s always possible to make a mistake. Don’t get too comfortable.
  2. Thoroughly clean out powders from hoppers, necks,drums, etc when changing loads.
  3. Always wear protective shooting glasses!
  4. Keep a reloading log and segment reloads into batches. Since I record and batch my reloads, I only have to pull a couple of hundred reloads instead of thousands.
  5. Always have first-aid on hand. I was lucky and didn’t need it, but it could have been very different.
  6. Always wear protective shooting glasses!

Thanks for tolerating my ramblings and stupidity; maybe this might help someone.
Cheers!


r/reloading • • 9h ago

Load Development 11.5in upper velocities?

1 Upvotes

Im getting ~3100 fps out of 26gr of tac with a 64gr tbbc (im pushing the limit i know) I was wondering what should I expect with a 11.5in barrel? I just got this upper yesterday im making some loads up for it right now just wondering what to expect vs 20in barrel.


r/reloading • • 12h ago

Newbie Did I ruin my brass?

Post image
7 Upvotes

I bought a box of ADG brass in .308. Also copped a new Matchmaster seating and full-length sizing dies from Rcbs. I ran the full box of cases through the sizing die and I saw that it left all these vertical marks inside and outside the case neck. What did I do wrong?


r/reloading • • 13h ago

I have a question and I read the FAQ I need to stop picking up random "brass"

Thumbnail
gallery
16 Upvotes

I fell victim to NAS3 300blk case I must of picked up at the range... How the hell do I get this out lol


r/reloading • • 15h ago

I have a question and I read the FAQ A1680 in 7.62x39 with 123 gr Gold Dots

Thumbnail
gallery
17 Upvotes

I've loaded several different bullets in 7.62x39 with A1680 and it has been the best for hitting factory plus feet per second speeds.

I've loaded 27.3 grains of 1680 under hornady sst 123 grain bullets hitting 2,471.1 fps. With a magnum large rifle primer.

The factory hornady black sst 123gr 7.62x39 was 2,267.3 fps out of the same AK.

So I'm getting ready to work up these gold dots and the data from speer looks kinda crazy to me of 28.2 grains of A1680 to hit 2,455 fps max. (Second picture)

I'm hesitant to work up to that charge. Obviously I'll start lower but wondering if anyone has experience loading this combo? I know the sst bullets are longer and sit deeper in the case causing more pressure but the 28.2 max charge for the GD still seems high.

Would you shoot for the 2,400 fps range for these bullets? I was a little surprised the hornady factory ammo was only 2,200 fps. I know these are different bullets but they are what I am working with right now. Looking for the best hunting load.

Do you use magnum large rifle primers when using spherical powder or not necessarily? I use the magnum with ball powders generally but regular large rifle primers with extruded powders.


r/reloading • • 15h ago

I have a question and I read the FAQ When should I throw out my brass and start a new?

3 Upvotes

I have reloaded factory Hornady 6ARC brass 9 times now without annealing. I haven’t seen any cracks but I am wondering when I should just throw it out and start on my bag of starline brass? What are typical failure modes? Is it safe to shoot until I see a failure? These are shot out of a bolt gun btw. Thanks


r/reloading • • 15h ago

i Have a Whoopsie I mistook 7.62 M80 range brass as being boxer primed, ugh...

Post image
8 Upvotes

I honestly didn't think I was applying that much force; I kind of automatically assumed it was the boxer-primed Austrian surplus Canada had gotten a ton of a few years ago and wasn't paying attention that it was Brendan.

I am just glad this is a $15 mistake that local shops can fix with replacement rod for my die.


r/reloading • • 16h ago

It’s Funny Thoughts? Concerns? 22creedmoor with m855a1

Thumbnail
gallery
10 Upvotes

r/reloading • • 16h ago

Newbie 9mm subsonic

Post image
34 Upvotes

Cranking out subsonic 9's with my Lee Six Pack progressive. Using 3.4 grns of titegroup to push 147 gr FMJRN at 1.145 OAL for range fun.
I consider myself a newbie as Im in my 4th year of reloading.


r/reloading • • 17h ago

Newbie Is a 50 grain copper bullet a good choice for hunting using an AR?

3 Upvotes

For an AR 223.

I’m primarily targeting small hogs for meat.

Yes, I have a 308, but I’d rather use the AR


r/reloading • • 1d ago

Newbie Off to a slow start with a rather rudimentary setup.

Thumbnail
gallery
21 Upvotes

r/reloading • • 1d ago

I have a question and I read the FAQ Which one of these powder measures is the most accurate with stick powder?

Thumbnail
gallery
25 Upvotes

Which one of these has the least deviation between charges with powders like Accurate 5744, IMR4198, H4350 and other stick powders?

I've been using the Lee perfect powder measure for over 6 years now and it has been ok but I'm trying to get into more matches and I've been needing to upgrade for some time now.


r/reloading • • 1d ago

It’s Funny Time per round. How long does it take you?

8 Upvotes

My friend (he's a shooter, but not a reloader, or a precision guy at all) asked me if reloading was 'worth it'. Brought up how much work it was to produce the ammo I was shooting.

I struggled to come up with a 't/round'. Guessing it's around 3 minutes per round for me for all the steps between cleaning to seating. Total guesstimate, likely on the low side.

What's your guy's 't/round' estimate?

Background: I shoot service rifle match competition 223/556


r/reloading • • 1d ago

Newbie Reloading help

Post image
8 Upvotes

Getting into reloading match grade rounds does anyone have a starting place for load development

I’m wanting to use the 168gr bthp from hornaday
With ram shot tack , I’ve found mins and maxes for 168gr sierra MatchKing with TAC suggested starting was 40.0gr and max load was 43.6gr.

Any help is appreciated


r/reloading • • 1d ago

I have a question and I read the FAQ Triple Checking 9mm Dillon XL750 Setup

1 Upvotes

Hi Guy!

I am finally ready to make the jump into reloading 9mm for USPSA. I am planning on starting with a Dillon XL750 and having a bullet and case feeder. My question is does this make sense for the 5 stages: 1) Case drops in and is sized and decapped 2) primer is seated and powder added 3) Bullet is dropped 4) Bullet is seated 5) Bullet is crimped. Does this sound right, or am I missing something?

And now for the extra stupid question: When I was looking into things a while ago I remember reading or seeing that a certain die set offered some unique feature over the other ones. Does this sounds like something or am I misremembering?

Thanks!


r/reloading • • 1d ago

I have a question and I read the FAQ What on earth?

Post image
20 Upvotes

I'm throwing Winchester 231 Ball Powder and this slowly emerges from the hopper. It's from a brand new 4lb jug. Any Idea what this could be? A messed up extrusion, maybe?


r/reloading • • 1d ago

Gadgets and Tools SDB chute

Post image
7 Upvotes

Second print on the X2D. Still need to drill a hole in the bench and get some tubing.

I have an idea for a case feeder but that’s a ways out.


r/reloading • • 1d ago

General Discussion Clean Gas gun powder?

0 Upvotes

Any suggestions on a clean burning powder for suppressed AR platform? I’m currently using tac. I love it. Just wondering if there’s anything that runs a little bit cleaner and less gassy?