r/AskAMechanic • • 17m ago

I hope it's a simple question

1 Upvotes

I just bought a wheel and tire package, want to reuse the old rims for winter tires next year..

is there an easy way to remove old run flats from beat up rims without beating them up too much?

they're already fucked up a bit with road rash, but good enough for a winter set of tires before next year..

my mind says, deflate, sawzall the tire into quarters without hitting the rim, and just snip the remainder near the bead.. and rims are clean..

any insight before I get my tools out?

I appreciate any advice.


r/AskAMechanic • • 33m ago

20011 Chevy avalanche Vortec engine. Was driving down the road going about 35 and it sounded like a deer hit the right side of the truck.

1 Upvotes

I don’t see any damage to the vehicle but it was loud, I stopped and looked all the way around and nothings there, gauges are fine as well????


r/AskAMechanic • • 35m ago

1.4tsi CAXA strange sound?

1 Upvotes

This sound apears only at iddle,and only when engine is on operating temperature.When driving,everything is normal.

No erors on diagnostics.

When i put my head near engine,i think it comes from front part od the engine.

Sound is like metal/valve whistle.

I drive like this for 5K km and sound dont get any lower or higher in volume.

Waterpump was my first gess,but its changed 15k km ago and sound of bad waterpump is like e-engine spining,constant noise but my noise have diferenr rytm.


r/AskAMechanic • • 36m ago

Weird noise when slow and stopped from rear. (2002 Toyota Tundra)

1 Upvotes

Truck makes a super annoying vibrating sound when Im in reverse or creeping slowly on drive, and makes it worse when I turn the wheel. only thing I saw that changes it for the better was lifting the driveshaft by the carrier bearing. any guid would be greatly appreciated. Thank you


r/AskAMechanic • • 55m ago

Transmission Fluid Clear/Amber After Top-Up?

2 Upvotes

Hey everyone,

I recently took my 2001 Subaru Legacy automatic for a transmission change/drain and fill(101000km). They told me my transmission fluid was extremely low, pretty much empty, and topped it up with approximately 1.3 litres.

They mentioned there could potentially be a leak. I’ve since been monitoring it and tried the cardboard trick overnight to see if I could spot any leaks. It looks like it could be coming from the driver-side area being pinkish so now I now I booked a mechanic.

The car drives perfectly fine. No slipping, clunking or delayed shifting.

I checked the correct fluids, and it looks very clear with a slight yellowish/amber tint rather than red. The level is now above the low mark.

Can transmission fluid look clear or amberish after being topped up with fresh fluid, or should I be concerned?


r/AskAMechanic • • 1h ago

Strange noise/braking after wheel change

2 Upvotes

2013 Nissan Altima, 270k KM.

Swapped out the summer tires for winter tires today. After installing, I took it for a small drive and there was horrible scraping sounds coming from the front and the brakes were spongy and aren't working well at all.

Jacked it back up to remove the wheel and 2 of the nuts/studs were stripped upon removal. I couldnt see anything out of the ordinary.

I may have overtorqued the nuts when installing. Would this cause all this?

Car is heading to the shop on Monday, but I'm just wondering what the hell I did wrong.


r/AskAMechanic • • 1h ago

Replaced Axle Seal, Still Leaking

1 Upvotes

2018 4Runner

Hey y'all, last week I observed my rear passenger brake assembly soaked in oil. I suspected a bad caliper and replaced, but it turned out not to be the caliper leaking. Did some more research and found the axle seal to be the next most likely culprit.

Purchased two seals and replaced both sides. Passenger side rear seal had a visible tear (the leaking side). When I pulled the driver side it was intact but tore upon inspection.

The original leaking side is still leaking after replacement. Bad install or something else? Looking back on the install I did not grease the seal with anything except giving it a smear of diff fluid.

What do you think? Pull leaking side, inspect, and replace again?


r/AskAMechanic • • 3h ago

Is my car leaking oil?

Post image
0 Upvotes

Just got a new (to me) 2019 Rogue. Only 60k miles. Had it visually inspected by my mechanic in Lieu of a ppi, as my mechanic had no room for an appt on the hoist that day unfortunately. He had said no red flags, no rust, everything Looked and sounded good, except there was a little oil wetness on something, I can’t remember what he said, but he said it could just be a drip from where they did an oil change so I didn’t worry about it.

The dealership also showed me everything they inspected. It drives great, and seemed to be in excellent shape. It had just had a transmission drain and fill as recommended by Nissan at 50k miles and was treated with rust proofing multiple times over its life. And oil changes every 6-7k miles So I felt confident it was in good shape.

I drove it for about an hour from the dealership, parked it overnight, and didn’t drive it again til the next evening, about 20 hours later.

When I came home, I parked in a different spot, and noticed the photo below. Not just a spot, but it’s trailing. I’ve never seen anything like that before. I goes for about 20-30 feet and tapers off. It was from between the front wheels. It didn’t evaporate several hours later, so I’m assuming it’s oil?

just curious if you can tell me what could cause this and is it safe to drive, and will the dealership do anything??? There’s no way they didn’t know about this, right? I noticed it Less than 24 hours after buying it. And they just replaced parts a day before.


r/AskAMechanic • • 3h ago

Triumph spitfire starter issue

Thumbnail
gallery
1 Upvotes

Issue - 1973 triumph spitfire - Car was running then died, starter & solenoid replaced, just get a clunk when turning key from solenoid. no voltage running off the red/white wire from the starter to barrel, (ignition wire?) loose double white wire not connected to a terminal (may have pulled off when taking cover off) Don’t think I can get a voltage reading with the switch disconnected, (runs off the key being turned?)


r/AskAMechanic • • 4h ago

Question about a 2002 Toyota 4Runner 3.4L V6 transmission?

1 Upvotes

How do I know when I need to have the transmission serviced? I bought it a couple weeks ago and it has 271K on it. As far as I know, the previous owners have never done it and the fluid is dark so I'll be changing that regardless, but when? And is that all I should do (to the transmission specifically, I'm doing other maintenance already), the fluid and filter? A rebuild kit crossed my mind but is that excessive? I've been told not to have it flushed because that can dislodge things and potentially cause slippage, especially if it was never done before. It starts and drives well, but I've noticed that if I have to slow down before a hill, accelerating to go back uphill is.... a bit of struggle? It goes, but it feels like it's dragging a little is the best way I can describe it, like I'm pulling a ton of weight or something but I'm not. I can hear a very faint whine noise when it's happening, like it's at risk of slipping? It sounds sort of like when you go to crank up a cold diesel or something, that "wha...wha...wha..." before it turns over and starts, but it only happens when I'm accelerating up a hill from a slow/stop and it's very quiet, I can only hear it with the radio completely off. Everything else about the vehicle seems fine, in every other way it drives great, but not knowing much about cars makes me nervous so I figured I'd ask some smarter people. Is this even a transmission issue? I've convinced myself it is but I don't know enough to be sure. Is this even a problem or am I just being a paranoid dumb girl about it? Idk. Any help is appreciated


r/AskAMechanic • • 5h ago

Could this be deliberate?

Post image
2 Upvotes

2021 Toyota RAV4 Hybrid

Hi. My car had a front suspension fix done two weeks ago at my usual garage, with no other problems reported with car, with car's UK MOT passed in October with only the nsf suspension fixed advised.

Two weeks later I take the car to a different garage for new front tyres and after removing the wheels they straight away tell me the NSF CV boot seal is damaged and leaking badly. See picture. It looks like something has punctured it, right in the seal edge.

Obviously, I can't prove the first garage has done anything malicious with the CV boot, but should I question this with them, as it is only two weeks since they last fixed the same side front suspension?

Should I trust the first garage with my car anymore?

Thanks for any advice.


r/AskAMechanic • • 8h ago

F150 power steering pump pulley bearing shot out , pump got hot and Mount bolts, Welding in place! Can' I grind heads off Have new pump + block bolts easy out stem+ old treads? 🤞🏻

1 Upvotes

2008 5.4 L v8 FX4 F150

CrewCab


r/AskAMechanic • • 9h ago

I need help

1 Upvotes

I own a 98 pontiac grand prix with the 3.8 L V6 and it's constantly overheating ive replaced the thermostat as well as had a coolant flush and it refuses to get coolant into the engine the water pump is not leaking and all the belts, hoses, and tubes are fine i have no idea what else to do


r/AskAMechanic • • 9h ago

25 F-150 Rear End Popping

0 Upvotes

My 2025 F-150 has been making a popping sound when the suspension is under load. It occurs when driving onto or off of uneven surfaces, like going off road or pulling into a ditch or steep incline from a flat surface. My friend and a couple other guys mentioned they think it could be a differential issue. My friend inspected it and deducted it wasn’t the leaf springs because he couldn’t feel anything while touching them while the popping was occurring. Here’s a video of me pulling into a ditch and causing the popping. Any advice or possible diagnoses are appreciated.


r/AskAMechanic • • 9h ago

Looking for advice to manage a muddy Undercarriage & Lower Front Bumper damage on my 2011 Toyota Hybrid Prius

Thumbnail
gallery
1 Upvotes

My under-car splash shield had to be ripped out months ago. At the time, a trusted mechanic told me I didn't need to replace it. Since then, the right side of my front bumper (passenger side) has started to hang a bit.

Tonight, I mistakenly drove into this huge muddy hole on an unpaved, county road. For about 30 seconds, my car was stuck and I had to reverse- fortunately, I got out.

Now, my bumper is fully sagging and the hood of my car is raised. I tried to take the best photos I could since I just arrived home.

I plan to take my car to the mechanic, but I’m wondering what to expect. The exposed undercarriage of the front end of my car is drenched in mud. What can I do to avoid any problems w/my car? Should I expect really bad news?

Also, please don't leave any mean or unhelpful comments. I got lost driving and followed google maps- which landed me in this worsened predicament. I appreciate any advice to help fix my issue.


r/AskAMechanic • • 10h ago

2017 Ford escape se 1.5l ecoboost coolant leak.

Thumbnail
gallery
1 Upvotes

Hello I need help getting the part number and name of the hose I have a leak of coolant and see that this hose is spraying out coolant when I squish it I can hear like a oozing spraying sound and hear it I need help identifying the hose so I could get the part and replace it thank you in advanced.


r/AskAMechanic • • 11h ago

2021 Lexus ES350 3.5L V6

Post image
0 Upvotes

My Ltft are high at idle. I smoked the vacuum line from the the intake hose into the compensated motor mount and there’s a leak at the engine mount. Out of this port. What does that mean. Are the internals busted? Any advice?


r/AskAMechanic • • 11h ago

Crankshaft Pulley Wobble

3 Upvotes

2016 Ford Edge 2.0L eco boost
I was using a stretch belt tool to change the serpentine belts. I tried removing the auxiliary belt with the tool a couple times but ended up cutting the belt to remove it. After changing the belts, the crankshaft pulley has a slight wobble to it. Is this enough to be concerned about? Was thinking of taking it to a mechanic after the weekend but thought id ask the crowd here until then. Thanks.


r/AskAMechanic • • 11h ago

how negative a thing would it be to remove that little shield piece around the brake area?

0 Upvotes

2019 Hyundai Santa Fe. That piece started rattling or at least I think that’s what it is on my left front tire whenever I make a right hand turn. It also rattles when I go over bumps. Someone said they thought they could just rip it off for me. I declined because I don’t know how important that is. also, I live in the north, so we are going into winter- heavy salt and snow.


r/AskAMechanic • • 12h ago

2005 4runner brake issue

0 Upvotes

I have a 2005 4runner sr5 v6 4wd and the brakes are acting up. I had the abs sensor unplugged for a while to disable traction control because there's no other way on this vehicle but I blew off the dust on the plug and plugged it back in because anytime I would hit a bump while on the brakes, after the bump, the brakes would just dig in. It recently started doing it on flat roads around 15mph so I thought I mightve been leaking brake fluid, but I looked at the hoses around the calipers and the brake fluid level and both were fine. I went to autozone and it pulled up codes

- p0328 (knock sensor bank 1)

- c0200 (front speed sensor)

- c1202 (brake fluid level low/open circut in brake fluid level warning switch)

- c1223 (abs control system malfuncion)

- c1253 (hydro booster pump motor relay)

- c1256 (accumulator low pressure)

I believe these are the same codes I had when the abs sensor was unplugged. I sprayed some electric cleaner in the connector to clean it out and topped it off on brake fluid and it didn't do it again during my 5 minute drive but the lights were still on.

If anyone could point me in the right direction I would really appreciate it.


r/AskAMechanic • • 13h ago

Mobile mechanic only bled one wheel and my parking brake came loose during the job. Reasonable to ask for compensation?

0 Upvotes

Looking for a sanity check and advice on how to handle this. Based in Southern California.

I supplied my own rotors and pads (ordered from RockAuto) and hired a mobile mechanic to install them plus bleed the brakes. He has a highly-rated Yelp page with good reviews going back about a decade, so I figured I was in safe hands. I've since learned he has no BAR (Bureau of Automotive Repair) registration, which as I understand it is actually required to do auto repair for the public in CA.

Total was $420 cash: $370 for the pad/rotor install and $50 specifically for a brake bleed. Here's what's bugging me:

He only bled one wheel. I paid for a brake bleed and he did just the front driver side, said that was "enough." My understanding is a bleed means all four corners in sequence.

He skipped slide-pin lube and didn't clean the hub mounting surface, even after I specifically asked him to. He said it wasn't necessary.

He never test-drove it or even started the car. If he had, he'd have seen the dash warning light.

My parking brake connector came loose during the job and won't reseat. It was completely fine before I handed him the car. He says it's not his fault, tried to fix it, couldn't, and left. The issue is right at the rear brakes he was working on.

I've now taken it to my regular shop where it’s $45 just for diagnosis, plus whatever the connector repair costs.

My questions:

Are the one-wheel bleed and skipped slide-pin lube / hub cleaning legit workmanship problems, or am I being picky?

On the parking brake, even if he claims that he didn't directly cause it, isn't failing to test the car and catch it on him?

What's reasonable to ask him for? I'm thinking the $50 bleed, the $45 diagnosis, and at least some cost on the connector.

Worth a BAR complaint / small claims if he won't cooperate, or not worth the headache over this amount?

I'm not trying to ruin a hardworking guy, just want my actual problems fixed and to be treated fairly. Appreciate any advice.

2015 Outback


r/AskAMechanic • • 13h ago

Broken stud

Post image
1 Upvotes

How easy is this to fix.

pajero nx 4m41


r/AskAMechanic • • 13h ago

Steering wheel shakes at 80km/hr

1 Upvotes

O have a 1997 Honda Acty Kei Van. Once I hit 80 km/hr the steering wheel starts to shake a lot. I’ve had the car over a year and have refused to go over 80. Is this a common issue? Is it a simple fix? I usually work on the car myself, so I’m up for a challenge if it’s more difficult to address. Got the wheels balanced hoping it would fix it but it persists. Wheels have been rotated and wobble hasn’t changed


r/AskAMechanic • • 13h ago

Do I Need to Replace My LCA Bushings Immediately?

Thumbnail
gallery
1 Upvotes

This is a Subaru Forester 2017. These are LCA bushings from my driver and the front passenger seat.

I have a long trip coming up, and I want to make sure if I need to replace them immediately for a long trip (~400 mi round trip in California, Bay Area) or it should be OK to drive and replace after.