r/AskAMechanic • • 14h ago

2015 Chrysler 200 Limited Caliper Bracket Bolt?

Thumbnail
gallery
6 Upvotes

I decided to replace my brake pads and rotors, I go to take off the caliper bracket bolt with my impact wrench 6 head 3/8 inch 17mm socket and it will not budge. I’ve tried heating it with blow torch. Nothing. Now I tried looking it up and one site says it’s a hex flange, other says e Torx. When to buy e Torx and they said they don’t sell 17mm in e Torx “it doesn’t exist” I’m pretty stumped.

I’ve attached photos.


r/AskAMechanic • • 17h ago

Help!

Post image
4 Upvotes

Does this look to be seated correctly?


r/AskAMechanic • • 10h ago

Crankshaft Pulley Wobble

3 Upvotes

2016 Ford Edge 2.0L eco boost
I was using a stretch belt tool to change the serpentine belts. I tried removing the auxiliary belt with the tool a couple times but ended up cutting the belt to remove it. After changing the belts, the crankshaft pulley has a slight wobble to it. Is this enough to be concerned about? Was thinking of taking it to a mechanic after the weekend but thought id ask the crowd here until then. Thanks.


r/AskAMechanic • • 17h ago

Would it be safe to air these up to roll em up on a trailer. 05 Buick la saber.

3 Upvotes

r/AskAMechanic • • 18h ago

Post-oil change, there’s a burning smell and faint whispy smoke

3 Upvotes

2019 Subaru Impreza. Got my oil changed yesterday and I noticed a burning oil smell when I got home. I just checked under the hood after letting my car warm up and there’s a little bit of smoke coming up from underneath somewhere. There are oil splatters here and there under the hood. No leaks, I checked for that. The oil is still pretty full and clean, I checked the dipstick. Smoke looked like it was coming from down below, maybe nearby the belts somewhere. It’s not thick smoke, just whispy. Should I be concerned?


r/AskAMechanic • • 13h ago

Steering wheel has been funky since I hit a ditch

Thumbnail
gallery
2 Upvotes

Hi all, I have a 2023 Hyundai Elantra Limited. I unfortunately hit a ditch in the dark and since then my steering has been funky. I got it checked at VIP tires near me and they took me to the rack and showed me play with both the control arms and one was significantly bent. I got them both replaced with a set of aftermarket control arms and also got an alignment (attached).

However, the steering still feels off. On a straight highway the steering loves to default to a tiny bit towards the right and I have to apply a gentle counter pressure for it to remain straight. On long rides I have to basically keep doing such micro-adjustments so that the car drives straight and very rarely I find a stretch of road where it'll go straight without my input on the steering wheel.

I took it back to VIP tires and they apparently fixed it but I saw no improvements. I'd go again but I want to know what to expect.

This issue is even more noticable on slope-y roads which happened to me today. I was at a red light and when I was centering my car by slowly going left, the steering wheel just didn't want me to steer left and felt very firm and stiff.

Thank you! I really appreciate any help!


r/AskAMechanic • • 14h ago

Car wouldn’t start today

2 Upvotes

Hello everyone! My partners car wouldn’t start today. I included a video of what it looked/sounded like. I’m originally from ND so I have seen my fair share of dead batteries but I have not heard a car make sounds like this when trying to start before so wanted to see if it’s just the battery or if something else needs replacing! It’s a 2018 Honda CR-V.


r/AskAMechanic • • 19h ago

Thump/slight knock sensation in the floorboard

Post image
2 Upvotes

PFA

Hi guys, I’ve got a strange issue that started happening recently.

Seat Leon Cupra st300 4drive & DSG (2018, dq250) with98k km.

Changed tires from summer to winter (SC7 to Hankook icept evo3) on the same set of rims (original 19” rims) - since that moment, I’ve got a thump/thud and vibration feeling in the floorboard after hitting 20mph. It feels like a click and it’s speed dependant.

It does it while cruising, coasting in N or breaking and downshifting, only after 20mph. If I’m accelerating hard and I stick with it, I can’t feel the thumps anymore.

I checked the tires and they had some bulges so decided to go for a brand new set of Hankook icept evo4. Mounted them again on the same rims, and to my surprise the issue is still there.

Note that there’s no audible noise, clank, hum or anything out of the ordinary apart from the normal winter tires noise. It’s just a sensation like a thump in the floorboard, parallel to the DSG gear shifter. This thump is felt on driver and passenger side and the vibration is felt through the steering wheel as well (slight, no play or movement in the steering wheel, just sensation)

What I’ve checked until now:

- tire pressure (tried 2.9 bar, 2.7, 2.6, 2.5 - across both axels - no difference)

- rebalanced the rims (once with the evo3 tires and second with the evo4)

- swapped front to back

- changed oils in front and back difs plus haldex and DSG

- checked the rotors (dba series 5000 - 8k km usage only street) not to be warped (I’ve got no vibration or steering movement while braking)

- checked the CV joints and axels and only the rear right side has like a 5mm play which I find very acceptable

- did the alignment on both axels (only front right could be set full in spec in camber, but it’s a 0.07 degree deviation)

- changed the dogbone mount (went for lemforder) as the OEM one was aged

- inspected the giubo (no play, no cracks)

While we raised the car and put it in drive at that speed, we couldn’t feel anything in the floorboard.

I don’t have sort of clanks or noises when accelerating while turning, or going more aggressive from a standstill (things that would indicate a CV issue) and I also tried to rev the engine in neutral at the same RPM I can feel the thumps while driving and it’s not doing it.

My mechanic told me that he suspects the wheel bearing (but I don’t have a hum and I changed both front bearings 4k km ago) or that all rims are rounded, but this doesn’t explain why with the same rims on summer tires I haven’t had any issues.

Could it be due to wheel bearings failing again?

Any ideas?


r/AskAMechanic • • 20h ago

F150 2.7L 2015 crank no start

2 Upvotes

Installed

New fuel injector

New fuel pressure sensor

New battery

New Fuel control module pressure

New spark plug

checked all fuses

still same.

CodeDescription
P0230:14-C8Fuel Pump Primary Circuit
B1048:01-88Brake Fluid Level Switch
B108A:24-48Start Button
B124D:02-8ATire Pressure Sensor

r/AskAMechanic • • 40m ago

Replaced Axle Seal, Still Leaking

1 Upvotes

2018 4Runner

Hey y'all, last week I observed my rear passenger brake assembly soaked in oil. I suspected a bad caliper and replaced, but it turned out not to be the caliper leaking. Did some more research and found the axle seal to be the next most likely culprit.

Purchased two seals and replaced both sides. Passenger side rear seal had a visible tear (the leaking side). When I pulled the driver side it was intact but tore upon inspection.

The original leaking side is still leaking after replacement. Bad install or something else? Looking back on the install I did not grease the seal with anything except giving it a smear of diff fluid.

What do you think? Pull leaking side, inspect, and replace again?


r/AskAMechanic • • 2h ago

Triumph spitfire starter issue

Thumbnail
gallery
1 Upvotes

Issue - 1973 triumph spitfire - Car was running then died, starter & solenoid replaced, just get a clunk when turning key from solenoid. no voltage running off the red/white wire from the starter to barrel, (ignition wire?) loose double white wire not connected to a terminal (may have pulled off when taking cover off) Don’t think I can get a voltage reading with the switch disconnected, (runs off the key being turned?)


r/AskAMechanic • • 2h ago

Question about a 2002 Toyota 4Runner 3.4L V6 transmission?

1 Upvotes

How do I know when I need to have the transmission serviced? I bought it a couple weeks ago and it has 271K on it. As far as I know, the previous owners have never done it and the fluid is dark so I'll be changing that regardless, but when? And is that all I should do (to the transmission specifically, I'm doing other maintenance already), the fluid and filter? A rebuild kit crossed my mind but is that excessive? I've been told not to have it flushed because that can dislodge things and potentially cause slippage, especially if it was never done before. It starts and drives well, but I've noticed that if I have to slow down before a hill, accelerating to go back uphill is.... a bit of struggle? It goes, but it feels like it's dragging a little is the best way I can describe it, like I'm pulling a ton of weight or something but I'm not. I can hear a very faint whine noise when it's happening, like it's at risk of slipping? It sounds sort of like when you go to crank up a cold diesel or something, that "wha...wha...wha..." before it turns over and starts, but it only happens when I'm accelerating up a hill from a slow/stop and it's very quiet, I can only hear it with the radio completely off. Everything else about the vehicle seems fine, in every other way it drives great, but not knowing much about cars makes me nervous so I figured I'd ask some smarter people. Is this even a transmission issue? I've convinced myself it is but I don't know enough to be sure. Is this even a problem or am I just being a paranoid dumb girl about it? Idk. Any help is appreciated


r/AskAMechanic • • 7h ago

F150 power steering pump pulley bearing shot out , pump got hot and Mount bolts, Welding in place! Can' I grind heads off Have new pump + block bolts easy out stem+ old treads? 🤞🏻

1 Upvotes

2008 5.4 L v8 FX4 F150

CrewCab


r/AskAMechanic • • 8h ago

I need help

1 Upvotes

I own a 98 pontiac grand prix with the 3.8 L V6 and it's constantly overheating ive replaced the thermostat as well as had a coolant flush and it refuses to get coolant into the engine the water pump is not leaking and all the belts, hoses, and tubes are fine i have no idea what else to do


r/AskAMechanic • • 8h ago

Looking for advice to manage a muddy Undercarriage & Lower Front Bumper damage on my 2011 Toyota Hybrid Prius

Thumbnail
gallery
1 Upvotes

My under-car splash shield had to be ripped out months ago. At the time, a trusted mechanic told me I didn't need to replace it. Since then, the right side of my front bumper (passenger side) has started to hang a bit.

Tonight, I mistakenly drove into this huge muddy hole on an unpaved, county road. For about 30 seconds, my car was stuck and I had to reverse- fortunately, I got out.

Now, my bumper is fully sagging and the hood of my car is raised. I tried to take the best photos I could since I just arrived home.

I plan to take my car to the mechanic, but I’m wondering what to expect. The exposed undercarriage of the front end of my car is drenched in mud. What can I do to avoid any problems w/my car? Should I expect really bad news?

Also, please don't leave any mean or unhelpful comments. I got lost driving and followed google maps- which landed me in this worsened predicament. I appreciate any advice to help fix my issue.


r/AskAMechanic • • 9h ago

2017 Ford escape se 1.5l ecoboost coolant leak.

Thumbnail
gallery
1 Upvotes

Hello I need help getting the part number and name of the hose I have a leak of coolant and see that this hose is spraying out coolant when I squish it I can hear like a oozing spraying sound and hear it I need help identifying the hose so I could get the part and replace it thank you in advanced.


r/AskAMechanic • • 12h ago

Broken stud

Post image
1 Upvotes

How easy is this to fix.

pajero nx 4m41


r/AskAMechanic • • 12h ago

Steering wheel shakes at 80km/hr

1 Upvotes

O have a 1997 Honda Acty Kei Van. Once I hit 80 km/hr the steering wheel starts to shake a lot. I’ve had the car over a year and have refused to go over 80. Is this a common issue? Is it a simple fix? I usually work on the car myself, so I’m up for a challenge if it’s more difficult to address. Got the wheels balanced hoping it would fix it but it persists. Wheels have been rotated and wobble hasn’t changed


r/AskAMechanic • • 12h ago

Do I Need to Replace My LCA Bushings Immediately?

Thumbnail
gallery
1 Upvotes

This is a Subaru Forester 2017. These are LCA bushings from my driver and the front passenger seat.

I have a long trip coming up, and I want to make sure if I need to replace them immediately for a long trip (~400 mi round trip in California, Bay Area) or it should be OK to drive and replace after.


r/AskAMechanic • • 13h ago

2011 Kia Proceed 1.4L VR-7 won’t start

1 Upvotes

5 degrees celsius here which i believe is causing the issue. I do find this odd considering i’ve heard cars should be able to start at lower temps than this.

My little obd2 scanner shows the real voltage sitting at 8.9v so i think it’s the battery but would love input from people more knowledgeable than me.

Only started driving this year and this is also my first car so go easy on me. Have made small repairs on it already and willing to make more if need be.


r/AskAMechanic • • 14h ago

Transmission comparable

1 Upvotes

My 2017 ford fusion se 2.5 needs new transmission. Pull a part has a 2015 se 2.5 how can I tell if they are compatible. Please be kind I don’t have tons of money to just buy one. I’ve googled verified the 8th digit of vin is same. Tr code on doors match.


r/AskAMechanic • • 14h ago

2015 Equinox headlight issue

1 Upvotes

Hello everyone. As in the title I have a 2015 equinox that has the right headlight out. I put a new bulb in it and it didn’t light up. Bought a two pack so I tried the other bulb, nope still out. (Turn single and running light works fine.

I have 12.xx vdc at the bulb connector. All the related fuses bcm) check fine.

I have checked the bulbs with a meter for continuity and they both appear to be good.

I replaced the connector with a new one only because the actual metal tabs didn’t look great and I was out of ideas. (Still get 12 vdc)

What should be my next process?

Thank you in advance.