r/Tile • • 20h ago

DIY - Project Sharing DIY master bathroom remodel. How did I do? All criticisms are welcome so I can improve

Thumbnail
gallery
82 Upvotes

It took 4 1/2 months of work to complete the project (including the closet which isn’t shown). I did all of the demo, framing, plumbing, electrical, tile, and quartz fabrication myself. How did I do? How can I improve? Thanks in advance!


r/Tile • • 45m ago

General Discussion Bought a house. Uneven tiles?

Thumbnail
gallery
2 Upvotes

Hello all. I apologize if these aren’t the greatest photos, I tried my best to show what I’m talking about.

Long story short, my wife and I just bought a house. What sold us on it was the finished basement. The whole basement floor is covered in this tile. The house was built in 1995 and well built. I am not sure if this tile has been here since then or if it was put in at some point between then and now. So not sure of the age. I like the idea of tile in the basement because it will be easy to clean.

However I didn’t really notice this until we started moving stuff down to the basement. Some of the tiles sit higher and lower than each other in some spots. Again I’ve tried to include a couple of photos of just one spot to show this best I can.

First picture if you notice the top right tile sits higher than the other 3 and has some lippage. Second photo you can also see how the tiles are not even with each other. The third picture is of our tv stand as you can see the front and back legs do not touch the floor, there’s a gap. (The other side of the tv stand the legs are touching the floor) so it’s making the tv stand wobble.

I have not taken a level or straightedge to any of the floor yet.

But what do you guys think? I’m a total idiot and novice when it comes to anything like this. Is this acceptable? Is it fine? There are no damaged tiles anywhere on the floor and there might be a very small hairline crack or two in the grout in a couple places but nothings damaged or loose.

I know there’s probably some acceptable measurements when dealing with tiles that are at different heights. And there’s a difference between even and flat? Idk.

Again am I overreacting? It’s kinda bummed me out, I was excited to have a “man cave” in this basement but kind of a bummer knowing I’m going to have to put shims or pads under any furniture I use in the basement to keep it even or from being wobbly.


r/Tile • • 12h ago

Waterproofing Is this shower properly waterproofed?

Thumbnail
gallery
5 Upvotes

I’m concerned about the floor-wall connection and wall seams. Our contractor used DensShield for the walls and a Schluter shower pan, with Kerdi Fix to seal the edges instead of Kerdi Band.
He’s confident that Kerdi Fix is sufficient, but every installation video I’ve seen uses Kerdi-Band at these connections.
I noticed the floor’s pretty beat up too, do we need this redone??


r/Tile • • 14h ago

DIY - Looking for Advice Colorado basement bathroom: faced insulation and poly behind backer board?

2 Upvotes

In Colorado, wild temp swings hot and cold. Basement bathroom.

For the shower wall thats against the exterior concrete in a basement, should we have faced insulation and poly behind the backer board, or should I unface the insulation and use only the poly behind the backer board? I don’t realize I technically created a double vapor barrier.

Red guard and tile has not been placed so I just need to remove the backer board to fix the issue, but what’s the right way?

Same question for the other shower walls that are on interior wall but not against concrete. I wanted to insulate these because a bedroom is on other side of wall. Should we add poly and faced insulation or just one?

*we are redguarding the entire shower floor to ceiling to ensure maximum waterproofing.


r/Tile • • 11h ago

DIY - Looking for Advice What are the best angle grinder blades, diamond sponges, and hole saws for tile that are sold at Home Depot or Lowe's? Looking for recommendations for my first tile shower build.

1 Upvotes

I have a Sigma B4U on order for my 12x24 tile. I'm going to need to make some square cuts around the niche and curb, a hole for the shower handle, and a hole for the shower head.

I'm guessing that I need a tile blade for my 4.5" angle grinder, a diamond sponge, and a hole saw for the 1/2" shower head drop elbow. I've seen lots of videos where the hole for the shower handle is made with an angle grinder, so I'm guessing that I don't need a 2nd hole saw for that.

I'd like to get the supplies locally, so whatever is available that's sold at home depot or lowe's.


r/Tile • • 1d ago

DIY - Looking for Advice Feeling defeated

Thumbnail
gallery
23 Upvotes

Struggling to get the floor flat. I am installing 12x24 with a ditra membrane. Allset under the ditra and versabond lft over the ditra.

I had to reframe some of the floor so it didn't come out very even, and I have old joists. 3/4 ply. So I figured I'd pour self level. Followed the instructions to a tee but did a bad job spreading it apparently. It turned out a little wavy and I had a low spot where I repaired. I used the exact measurements of water the bag called for. It's TEC 323.

I've put over a bag and a half of patch over the self level and I still have some bumps and dips. I took a diamond cup wheel to my high spots and filled in low spots but keep finding more issues. I've mixed the feather finish like 4 times now. More dips. More humps. Doing my best and I feel like I'm good with the patching work, but then I put my 6 foot level on it and I'm honestly horrified...

At this point I'm really fed up. I need to get this bathroom done and I'm finally at the final stages and I spent two whole days messing with this. Its starting to seem like I'm gonna spend a whole week getting it flat

Any advice for a first timer? I'd really appreciate any insight you can provide. Putting my all into this project trying to do things the best I can and it's humbling me. I am honestly losing hope in my ability to do this. LOL Thanks


r/Tile • • 13h ago

DIY - Looking for Advice I think I created a triple moisture barrier (facepalm)

Thumbnail
gallery
1 Upvotes

I’m in Colorado remodeling basement bathroom. When I demoed the shower, there was blown in insulation and thick poly behind the exterior wall. The insulation had fallen down so I added faced fiberglass insulation, then new poly, and hung the backer board.

Luckily we have not red guarded yet, so there is still time to correct. Should I remove the poly and faced fiberglass insulation?

I read that I should remove the blown in insulation and just add Rockwool Comfortbatt on all three walls (exterior concrete wall, and two interior shower walls). Then use redguard as the only moisture barrier.

Second issue (maybe): on my bathroom (non-shower) wall that against the exterior with concrete on the other side, I installed a new water shutoff for my hose bib outside. To do this we had to cut the poly and planned to install an access panel. Since this panel is in the bathroom, do I need to worry about moisture now getting back there since I cut the vapor barrier to install the shut off?


r/Tile • • 14h ago

DIY - Looking for Advice Palisades shower tile

0 Upvotes

I have a window and want to add a niche to my tube/tile surround. I do not want to use regular tile and my most preferred would be tile panel board but I can't find any information on what product to used that I can cut out a window and niche from. If anyone has a recommendation for that it would be appreciated but if not, can anyone give me advise about safely doing a window and niche in my shower area


r/Tile • • 19h ago

DIY - Looking for Advice Tile for fireplace- suitable?

Thumbnail
gallery
2 Upvotes

I found this tile, its aluminum on the front and i think ceramic backing? The specs are limited. It does say heat resistant, but no temperature rating or any more details.
What specifications are required for tiling around a wood burning fireplace ? Could /would this be suitable?


r/Tile • • 17h ago

DIY - Looking for Advice Kerdi shower pan help

Thumbnail
imgur.com
1 Upvotes

I have 32”x60” shower I’m trying to install a kerdi shower pan in, I’ve run into a plumbing issue. My pan has the drain on one side(not centered). My problem is right where the drain is, my toilets waste line goes right under it.

What can I do? I was thinking of trimming the one end so the drain moves closer to the wall, I can’t use a center drain because a joist runs exactly 30” from either wall. My worry is, if I trim the end the kerdi flange is going to be cut off so I’m afraid it will leak.

Any ideas?


r/Tile • • 17h ago

Tile Identification Help us Match This Tile

Thumbnail
gallery
0 Upvotes

12 x 24
Matte finish

We are needing to tear out our shower because the weepholes are clogged and are causing odor in our bathroom. We were hoping to be able to just replace the shower pan and maybe one row of tiles; however, we are having trouble finding a match for this tile. The previous owner was unable to help us. Any help would be greatly appreciated!


r/Tile • • 23h ago

DIY - Looking for Advice How to fix this edge

Thumbnail
gallery
3 Upvotes

What would be the best way to hide the reddish edge of these tiles short of redoing them?


r/Tile • • 17h ago

Homeowner - Advice about my Contractor Did I just get scammed

Thumbnail
gallery
0 Upvotes

Looking for a sanity check from pros or anyone who’s had a shower re-grouted before I hand over any money.

I was quoted nearly $900 for a full re-grout of my shower tile, which included a specific $100 line item for steam cleaning the tile. 1)The grout lines don't match—it looks patchy instead of one consistent color throughout. 2)It doesn't look like they actually ground/scraped out all the old grout before applying the new stuff. 3) Tile still looks pretty dirty in parts, even though there was an explicit charge for steam cleaning it.

For $900, I expected the old grout to be completely removed and the finished product to actually look uniform and clean. Am I being unreasonable here, or is this a botched/shortcut job?


r/Tile • • 21h ago

Waterproofing Possible to waterproof a partial wall repair?

2 Upvotes

I’m a plumber who’s fixing another plumbers shower valve screw up for a customer. Long story short, valve needs to come out, it’s a bathtub with a full tile surround about 3 years old.

Is it possible to remove a few tiles, cut a hole in the backerboard so i can replace the valve, put a new piece of backer board in, waterproof the seams between the replacement patch and the existing board, then retile?

I have been told by two tile guys that the entire surround must be replaced as you cant waterproof a section like that. I know nothing of tile, i accept that replacing the whole thing is probably the safest solution, however i can’t wrap my head around why it isn’t possible to

1: remove tile
2: leave 2-3” of backerboard protruding past the tile that is remaining untouched
3: install the new piece of backerboard and slather reguard or other waterproofing material over the seam
4: retile

Is it actually impossible or is it just a tedious annoying job that is not lucrative enough?

Thanks


r/Tile • • 1d ago

DIY - Looking for Advice How to repair?

Thumbnail
gallery
3 Upvotes

Fathers of Reddit! My girlfriend’s dad is in construction, but is estranged and we have no one to ask about this, so now we are here asking for help…

Water seems to be getting through the floor and down to my guest bedroom ceiling. There are holes all along the threshold (first close up picture) and in the corners where the floor meets the walls.

I am wondering if there is anything I can do to fix this myself, the shower is 3 years old.

Thanks in advance…


r/Tile • • 23h ago

DIY - Looking for Advice Haze remover? Can I do this myself?

1 Upvotes

I had tile installed and the next day, it looked kind of dusty. Mapei FA grout was used. The contractor is booked on other jobs and can't come back to fix it.He told me to buy the cleaner/haze remover and do it myself.

I'm a little bit annoyed by that. To me, it's the contractor's responsibility.

Nevertheless, the grout company told me to buy Mapei Heavy Duty cleaner, which seems pretty toxic.

Can somebody tell me the best and safest way to use this product?


r/Tile • • 1d ago

Tile Identification New Home Build - budget cuts

1 Upvotes

Im looking for advice from professionals on how to save money in my bathrooms on a new home build. Disclaimer: I understand tile is an art and skill cost money. I am in no way shape or form looking to short change someone on their labor expense.

I know nothing about tile options. Im building a home with 3 bathrooms. 2 will have walk-in showers and tile floors. One will have a tile surround over the tub.

I dont have any preset ideas of what I want the tile to be. Honestly, as long as it looks nice, I dont really care, I'm really flexible. As I'm picking out tile and working with the contractor, all I keep hearing is "tile is expensive". Cool. How can I make it less expensive? Are there any alternatives to tile or different types of tile? Knowing I have to have a waterproof area and I dont want it to look cheap, are there any ideas or tips to keep the costs down?


r/Tile • • 1d ago

General Discussion Builder said there is no hollow tiles

Thumbnail
youtube.com
1 Upvotes

I send this to the builder and told them to check their installation as I found many hollow tiles. The supervisor not only said the installation is done well but he didn’t find a single hollow tiles.


r/Tile • • 1d ago

DIY - Looking for Advice Should i grout seal with this?

Post image
1 Upvotes

Im doing glass tile so it recommends unsanded and no aggregate. This is one pf few options. It has 2 stars for stain resistant so idk. All the higher quality ones have sand and aggregate.


r/Tile • • 1d ago

DIY - Looking for Advice Bought a house 6 weeks ago… shower already leaking downstairs. Loose stone, crumbling mortar, and trapped moisture. How screwed am I?

Thumbnail
gallery
15 Upvotes

We purchased and moved into a house about six weeks ago, and I'm already dealing with a leaking second-floor primary shower. Hoping some experienced tile contractors or waterproofing specialists can offer any advice!

Here's what's happened:

  • The shower worked without any noticeable leaks for the first several weeks.
  • About two weeks ago, I gave the shower an extra-deep cleaning.
  • Last week, we discovered approximately ½ cup of water leaking downstairs through the pocket-door frame in our kitchen pantry, immediately following a shower.
  • A plumber inspected the situation and recommended removing the old silicone caulking, re-caulking the shower, and reattaching two loose engineered-stone components.
  • The horizontal stone threshold directly beneath the glass enclosure is loose, as is a triangular corner shelf/footrest inside the shower.
  • The corner shelf was so wobbly that I could lift it off by hand. Underneath is a tan/white bonding material that crumbles apart like sandy peanut brittle or dried paste. There's a darker gray material beneath it.
  • Rather concerning, the shower hasn't been used for FOUR DAYS, yet the crumbling material and the underside of the stone shelf were still damp to the touch.
  • The loose threshold appears to have similar deteriorating bonding material underneath, although that area doesn't seem damp. I haven't removed the threshold.

My questions:

  1. Does this look like deteriorated thinset, mastic, or something else? Is this normal after only about nine years? (House built in 2017.)
  2. Does moisture trapped beneath the stone after four days suggest failed waterproofing, or could water simply have entered through deteriorated silicone?
  3. Could the loose corner shelf or threshold explain the leak into the kitchen below?
  4. Is this potentially a straightforward DIY repair involving removal of the old bonding material, reattaching the stone, and re-caulking? Or am I looking at something considerably more serious?
  5. How could I go about repairing this corner shelf and the threshold?

I'm fairly handy and initially planned to tackle this myself, but the more I uncover, the more concerned I am about concealing a larger waterproofing problem.

I'd really appreciate any advice on what I'm looking at, what to investigate next, and whether a localized repair is realistic.

Photos and video of the crumbling material attached. Thank you so so much in advance!


r/Tile • • 1d ago

General Discussion A tiled shelf

Thumbnail
gallery
4 Upvotes

Knelt for 3 days and now my knees hurt.


r/Tile • • 1d ago

Professional - Looking for Advice Non-obvious helpful tools

2 Upvotes

I work for a residential company as a carpenter, do a decent amount of tile for them but have come to really love it and have started picking up some side jobs setting tile. I have a basic set of tools (grinder, wet saw, some shitty trowels, diamond sanding pads, float, etc.)

Would love some recommendations for some "quality of life improvement" tile tools that I might not know about. Also favorite trowel brands? Want to pitch my $5 ones for a couple of nice ones - been looking at Primo, Raimondi, etc. just not sure what to go with.

Thanks! Been great reading this sub as I've gotten more interested in tile work.


r/Tile • • 1d ago

Homeowner - Advice about my Contractor Any creative solutions?

Thumbnail
gallery
2 Upvotes

Any creative solutions before my tile guy grouts this huge gap? I paid for the plumber but the tile guy is a family friend. Says its impossible to cut a piece that thin 🤷🏼‍♂️


r/Tile • • 1d ago

Tools or Materials Is this an acceptable finish for mitered shower niche corners, or should we ask for them to be redone?

Thumbnail
gallery
2 Upvotes

We just had the tile work completed in our bathroom renovation and opted for mitered edges around the shower niche instead of Schluter metal trim.

Our tilers mentioned that mitering could result in more chipping during cutting and potentially require extra tile due to waste, which we completely understood. However, we were never told that achieving a clean finish might not be possible or that we’d need to compromise on the quality of the final result.

Fast forward to the tile being installed and grouted, and we’re noticing several areas along the mitered edges with visible chipping that also feels rough and slightly sharp to the touch.

Is this something worth pushing to have redone, or is this simply the reality of choosing mitered corners on glazed tile?

For additional context, the tilers used a tabletop dry-cutting saw and a handheld angle grinder. After doing some further research, I’m wondering whether a wet saw with an appropriate blade could have produced cleaner cuts.

Would appreciate any perspectives from professional tilers or homeowners who’ve dealt with something similar. Thanks!