r/e39 • • 7h ago

525i appreciation

Thumbnail
gallery
99 Upvotes

r/e39 • • 9h ago

Reverse lights won’t work after engine swap

Post image
18 Upvotes

I had an engine swap done, I had a 520D and the engine and other components were taken from a 530D Touring, and I’ve noticed that the reverse lights don’t work.

Here’s what I’ve checked so far.
-fuses
-bulbs
-transmission switch

I’ve heard that the wiring on the touring is different from the sedan, and that whoever did the swap didn’t take that into consideration when wiring it.

Any ideas?


r/e39 • • 7h ago

So hows your weekend going?

Post image
10 Upvotes

Front jacking point is done for. But it will get welded again im far too deep into it now.


r/e39 • • 3h ago

E39 525D coolant leak

4 Upvotes

Hey everyone!

I have a 2001 BMW E39 525d, and I’m dealing with a pretty serious coolant leak.

The car loses around 1 litre of coolant overnight.

Winter is just around the corner, and temperatures are starting to drop below freezing.
I have to drive the car to work early every morning, so leaving it parked isn’t exactly an easy option.
I currently have about 1 litre(around 1qt) of spare coolant left, but obviously that’s not going to last forever at this rate.
As you can see in the video, the coolant is dripping directly onto the belt and then running off the belt onto the ground.
What would be the smartest decision in this situation? Would you keep topping it up and drive carefully until the leak can be fixed, or stop driving it altogether?
Could the leak be coming from somewhere above the belt? Has anyone experienced something similar on their E39 M57?
Any advice or suggestions would be greatly appreciated!


r/e39 • • 2h ago

Pixelfix LCD Repair - What is this foam strip?

Thumbnail
gallery
2 Upvotes

Greetings! I’m working on replacing my ribbon cable and LCD screen. My pixelfix repair kit came with this little foam strip but I’m not sure what to do with it. Anyone done this repair before that can shed the light? They have a little video but it doesn’t show this strip being used.

TIA!


r/e39 • • 2h ago

M52 single-VANOS running rich only in bank 1

2 Upvotes

Pic for attention.

My early M52 528i was stalling at idle and running pretty rough. I found several issues like a poorly adapted crank sensor, a couple of vacuum leaks and I replaced a lot of parts like plugs, fuel filter, ICV grommet, etc. and it's running a lot better, but one issue persists:

There is a 202 code (Lambda Regulation Bank 1 Post Cat) which points to fuel trims reaching the limits but only in bank 1. I can still hear faint popping from the exhaust so it's clear the code is right.

How can I be getting mixture problems in just one bank? I've yet to replace the pre-cat O2 sensors but they're $200 each. Most people who report mixture codes naturally see two codes, one for each bank.

I'm out of fresh ideas. Should I just keep throwing money at the problem and get the O2 sensors?


r/e39 • • 1h ago

2002 530i auto w 228k miles should i change transmission fluid?

Thumbnail ebay.io
1 Upvotes

i made a post yesterday about some fault codes that are causing me to fail smog, one of which is P0741 (torque converter clutch circuit performance/stuck off). there is no noticeable slipping and the manual shifts work fine 1-5. either way i figure i probably need to get the torque converter changed. right now im looking at this remanufactured TC on ebay and labor in mexico a friend of a friend quoted me around 3000 pesos (160ish usd).
for anyone who’s had this problem before i have two questions:

  1. what are the odds that its just the TCC solenoid causing the issue and if i change that could it solve the problem? also if i change the torque converter, should i also replace the solenoid at the same time?
  2. should i also have my transmission fluid changed? the car is at 228k i bought at 197k and as far as i know, it probably hasnt been changed. there’s conflicting advice on forums if you should just leave it because it’s high milage or change it every 60-75k miles.

r/e39 • • 1d ago

Illuminated door handles e39

Thumbnail
gallery
87 Upvotes

I developed a retrofitting kit for the illuminated door handles, relatively easy to install and oem looking. DM if you are interested


r/e39 • • 1d ago

E39 lights and speedometer

Thumbnail
gallery
37 Upvotes

My headlights stay on even when the switch is powered in the off position. Also, my speedometer is intermittent as a relate to working.

What could these issues be?


r/e39 • • 1d ago

ABS module heat shield

Thumbnail
gallery
45 Upvotes

Put this together today after hearing all the horror stories about these Bosch ABS modules cooking themselves in the engine bay.

For anyone who’s been running a similar setup for a while: does a heat shield actually make a noticeable difference in keeping them alive, or is it mostly just peace of mind before the internal bond wires eventually give out anyway?


r/e39 • • 18h ago

Fiancé got hit in 2002 530 I

Thumbnail
gallery
4 Upvotes

I found a 98 540. I don’t know if it’s the same color but I can get the hood the fender and the radiator support for 250. Should I do it and is it the same color? Someone tell me I said about 95% cosmetic. The only part of the frame has been is the fender got pushed in a little bit and so that part of the frame got pushed in I could take a heat gun to it. What should I do?


r/e39 • • 11h ago

ac/heat wont turn off

1 Upvotes

2003 530i occasionally my ac and heat wont shut off when i remove the keys from the ignition, anyone else experience and know how to deal with this? ive had to disconnect my battery for it to shut off.


r/e39 • • 23h ago

02 530i California smog test problems

1 Upvotes

Im trying to get my car to pass smog but it failed due to 3 codes:

-P0741 (torque converter clutch circut performance/stuck off)

-P1112 engine coolant temp sensor high output

-P1512 DISA or intake manifold

i need help figuring out how to fix the first and last codes. i have another radiator temp sensor so hopefully that clears the second code. does anyone have experience with these or know what i need to replace?


r/e39 • • 1d ago

Aislamiento headers y turbo

Thumbnail
gallery
18 Upvotes

Se que los motores diésel no son para todo el mundo, pero quería mostrar mi trabajo en la gestión térmica de mi m57d30 de mi e39 que estoy restaurando con 160.000km. Siempre pensé que la posición del filtro de aire estaba demasiado expuesta al calor del turbo/escape. Y ahora con las piezas fuera del coche me dió por probar.

Se trata de una primera capa autoadhesiva de cerámica mas o menos 4mm envuelta en una capa fina de inoxidable soldada por puntos.

Teóricamente este sistema conserva internamente el calor de la combustión manteniendo los gases de escape más calientes, por ende conservando mayor energía cinética, moviendo el turbo con mayor facilidad y evacuando mejor.

Esto yo no puedo demostrarlo, pero creo que por probar que no quede. Al menos, aisla del calor al modulo ABS mejor.


r/e39 • • 1d ago

New E39 discord sever!

5 Upvotes

Just made a new E39 discord server to help with any trouble shooting you guys have or for buying and selling parts the name is Worldwide E39 and the code is https://discord.gg/jUx7wCwf5 (any help making the server would be much appreciated as well!)


r/e39 • • 2d ago

You can use Turn signals in GTA and I did not know. Must be a BMW thing.

Post image
103 Upvotes

r/e39 • • 1d ago

Obnoxious squeak after rear brakes were replaced

4 Upvotes

I have this horrible squeak... it's tied to wheel speed, goes away when I lightly press the brake. Started happening after I replaced the rear brakes.
Zimmerman Z-coat rotors, akebono pads. I'm not sure what to do about it. It's very loud and obnoxious.
Caliper is new, brake hoses are good, caliper bracket is new. What else could it be? Thanks..


r/e39 • • 2d ago

Out enjoying a 60° November day

Post image
173 Upvotes

Had to get in some driving before winter hits and the roads are covered in salt. I need to move south one of these days 😂


r/e39 • • 2d ago

I am one of yall now.

Post image
133 Upvotes

E39 528i 5 speed.

We up!

Lmk any good resources to look for mods and parts.


r/e39 • • 2d ago

Looking to get into an 540i Touring w/ Manual Swap

6 Upvotes

Hey everyone,

I'm looking at a 2002 540i Touring just north of $15k with a 6-speed manual from an M5 and wanted to get some opinions from people who know these cars better than I do.

I've seen some pictures of the records, and there's seemingly a decent amount of history behind the car, and its well taken care of, and major maintenance has been taken care of too.

I'm not afraid of DIY maintenance or getting my hands dirty. I understand these are 20+ year-old BMWs and that ownership isn't going to be entirely trouble-free.

For those of you who have owned these cars, particularly the M62TU 540i:

  1. What would you be looking at particularly closely with 207k miles?
  2. Assuming the timing chain guides have been properly replaced, how much peace of mind does that actually give you?
  3. Are there any Touring-specific issues I should be aware of?
  4. How realistic is daily driving one of these today, including occasional winter use?
  5. At this mileage, what would make you walk away regardless of the maintenance history?

And ultimately, does a well-maintained example like this still make sense to buy, or am I romanticizing the E39 a little too much?

Appreciate any input. I'd rather hear the honest experiences, good and bad, from people who actually own these things.


r/e39 • • 2d ago

What is this hole on the transmission housing next to the starter?

4 Upvotes

Trans is an auto GM 4L30E! Doesn't seem to be any plug for it but never seen this before.
https://www.realoem.com/bmw/enUS/showparts?id=DP63-USA-06-1999-E39-BMW-528i&diagId=11_7518


r/e39 • • 3d ago

NEED HELP! 530d violent vibrations and loud metallic clacking, got MUCH worse after replacing crankshaft pulley.

9 Upvotes

Hey everyone, I’m at my wit's end with my 1998 E39 530d (M57, 184hp, manual) and I really need some advice before I throw more money at it.

The Original Problem:
The car had violent vibrations, bucking/jerking, and metallic clacking sounds, especially around 2,000 RPM (right around when the turbo spools/under load).

The car already has:
• Brand new Dual-Mass Flywheel (DMF) and clutch.
• New shock absorbers.
• Wheels are brand new and completely straight.
• I haven't replaced the engine/transmission mounts yet—I have the new parts ready to install next week—but the current ones aren't completely destroyed).
• Previous owner said he checked the injectors, but I might get a check on them.

What I just did (thought it was the pulley):
I inspected the crankshaft pulley (harmonic balancer) and saw that the vulcanized rubber was visibly torn. I was 100% sure this was the root cause, so I bought a brand new harmonic balancer, tensioners/idlers, and belts.
I had a local mechanic (a good Mercedes specialist, since I don't have a reliable BMW indie nearby) install everything.

The Current Situation (Much Worse):
Right after picking the car up, it is completely undriveable.
It’s now making loud metallic CLACK noises even at 1,000 RPM.

Looking at the engine bay while it runs, the new pulley seems to be wobbling/shaking a lot.

Every time it makes the loud clacking sound, the engine (especially the air filter box side) jumps violently.

Diagnostics & Mechanic's Opinion:
The mechanic told me he thinks it’s an injector or fuel pump issue when the turbo spools and suggested taking it to a diesel injection specialist.
However, the last time I checked with INPA, the injector correction values at idle looked fine(-0.3,0.4,-0.2 etc..)
I did previously have a Crankshaft Position Sensor fault code stored in INPA but now idk why my INPA stopped working a few months ago.

My Questions:

  1. Could the mechanic have installed the new Corteco pulley incorrectly (e.g., missed the dowel pin on the crank hub or torqued it unevenly), causing this wobble and making the car way worse?
  2. Or could a bad injector / fuel delivery issue / failing crank sensor really cause the engine to jump and clack this violently even at 1,000 RPM?
  3. What should be my next step here? Should I tow it back to the mechanic to double-check the pulley installation first, or look into the crank sensor/injectors?

Any help is massively appreciated!


r/e39 • • 2d ago

Intake valve help

2 Upvotes

Need help finding the valve that connects to the back of the intake that affects the abs. Beamer tech said that’s what is Messing up my brakes. Included vid shows where he said it goes, I’m not sure if it’s behind the screw or lower a little but it goes back there


r/e39 • • 3d ago

Style 42 Restoration

Thumbnail
gallery
47 Upvotes

Hey everyone wanted to seek some advice on how to restore these Style 42s. The faces look great, but the lips are peeling extremely badly with the metallic/ clear coat layer chipping off every time I touch the wheels. I was wondering how to approach making these nice again because they’re currently an eyesore