r/fixit • • 2m ago

How do I remove this from the wall?

Thumbnail
gallery
1 Upvotes

Replacing a Bathstore shower screen and can’t see how to detach the aluminum strip holding the glass from the wall. Are there secret screws somewhere?


r/fixit • • 1h ago

Screen doesn’t turn on anymore

Post image
3 Upvotes

Samsung smx f34lp.
Just used once, bought it from Vinted. It worked when I bought it but I wanted to use it again and the screen does not turn on. Ive tried every bottom and still nothing.
Someone any advice?


r/fixit • • 1h ago

FIXED How can I lubricate this door hinge?

Thumbnail
gallery
2 Upvotes

My door squeaks when opening and closing.

The hinges look like this (see pictures). I've tried turning the top part, but it doesn't seem to come off.

How can I lubricate these hinges? Is there a way to remove the top part?

Thanks!


r/fixit • • 4h ago

open Cat carabiner broke

Post image
0 Upvotes

I got it in June, I started using it to hang up an over the door organizer on a hook starting September to November 22. It was fine and presented no issues during it but I would occasionally put heavy stuff in the organizer like my phone and headphones on it and then I tried to remove it today and it was kind of buggy so I used a bit of force and then next thing I knew it snapped off </3 any help would be appreciated


r/fixit • • 6h ago

Window opening crank fell off

Thumbnail
gallery
0 Upvotes

Previously just put in the metal rod/pin thingy and it got back to working, but now a second piece fell out and I’m not sure where it goes.


r/fixit • • 8h ago

Toolbox lock jammed

Post image
1 Upvotes

We have the keys, it’s in unlocked position but the centre bit is meant to pop out and won’t. Anyone have any hot tips to unlock it?


r/fixit • • 9h ago

fixed Samsung Smart TV. Turns on then begins to flash like a strobe light.

0 Upvotes

It's done this before, but fixed itself. This time it's just doing it over and over and not fixing itself.

Tried doing a factory reset and unplugging but nothing works.

Here is the text from the TV's Rear Label

* Brand: SAMSUNG

* Model / Modele No.: UN50TU690TF

* Model Code: UN50TU690TFXZA

* Type No.: UN50TU690T

* Typical power: 66W

* AC: 110-120V~50/60Hz 125W

* Manufacturer / Distributor: SAMSUNG ELECTRONICS AMERICA INC., 85 CHALLENGER ROAD, RIDGEFIELD PARK N.J. 07660-2112, U.S.A.

* MFD. / Fabrique: AUGUST 2023

* Origin: MADE IN MEXICO(SAMEX) / FABRIQUE AU MEXIQUE(SAMEX) / HECHO EN MEXICO(SAMEX)

* Version No: X227 / UTU690T / UTU7000K-U50TK1

* S/N: 0ELG***********

* Contains Tx FCC ID: A3LWCT730M


r/fixit • • 9h ago

remove water stains

Thumbnail
gallery
1 Upvotes

bought a window off marketplace but got a little rain on it as i was carrying it in. how can i remove these water stains?


r/fixit • • 9h ago

open Victorian Wine/Booze Cabinet

Thumbnail
gallery
1 Upvotes

Wife and I just closed on this gorgeous older victorian home not long ago. She was polishing a built in bar cabinet in the dining room and tried to finesse one of the shelves back in but cracked the glass pane. She's absolutely devastated and doesnt think we can find a way to restore it because of its age and delicacy. Surely someone out there has a suggestion


r/fixit • • 10h ago

fixed How to unlock this door?

Thumbnail
gallery
1 Upvotes

I locked my bedroom door.

It has the button that you press in to lock the door on the other side. I pressed that in (idk why) and closed the door but now it won't unlock. I have the key to the door but it doesn't even turn when its in.

There is a small hole (last photo) in the knob that I have tried pushing pins in and nothing has changed.

I am a uni student so I really cannot afford a locksmith. This is a flat i'm renting so I also cannot afford to damage the door.

Any help would be much appreciated.


r/fixit • • 12h ago

Fantech WG9 Katana wireless mouse teardown: PCB photos

Thumbnail
gallery
1 Upvotes

Device: Fantech WG9 Katana wireless mouse. The PCB is marked "Kanata Wireless WG9 240603". I couldn't find board photos of it anywhere online, so I've included mine.

Problem:

  • The cursor suddenly stopped moving.
  • Left and right click, the scroll wheel, the side buttons, and the RGB all still worked.
  • The red sensor LED on the bottom was not lit.
  • The battery is fine (702535 LiPo, 3.7V, 2.22Wh) because the RGB and buttons work.

What I tried:

  1. Opened it up and unplugged the battery.
  2. Peeled back the insulating tape to inspect the sensor chip. I found no visible burns, corrosion, or damage.
  3. Tapped one of the sensor pins with a small screwdriver, and the sensor LED lit up and tracking worked again.
  4. Put tissue between the PCB and the bottom shell (away from the battery) and reassembled. It works normally for now.

My guess: a cracked or cold solder joint on one of the sensor pins.

Questions:

  • Does this sound like a bad solder joint, or something else?
  • Is reflowing all the sensor pins with flux the right fix?
  • Is there anything else I should check?

r/fixit • • 13h ago

How would you connect these ends?

Post image
0 Upvotes

r/fixit • • 16h ago

open Is there a way I can switch these armrests around with each other without disassembling anything other than the armrests?

Post image
0 Upvotes

I've had this chair about a week now. A family member assembled it for me while I was out of the house ans im just wondering if its possible to switch the armrests around with one another, since the right armrest is actually the left and the left is the right. Is it possible to switxh them around without disassebling anything other than the armrest? And will them being in their correct spots fix how the armrests are now? Its quite uncomfy, since they're barely facing forward at all, meaning barely any of my arm other than my elbow is on the armrest. Thanks in advance for answers


r/fixit • • 16h ago

Door key cracked and bent

Post image
0 Upvotes

Renting a condo and my door key fell really hard on stone tile and cracked and bent out of shape at the thinnest point. Is this fixable either diy or at a keysmith? Really rather not lose my key deposit. Thank you!


r/fixit • • 17h ago

open Ripped or cracked screw in point between wooden table and load bearing wood table leg

Post image
1 Upvotes

Hello everyone, I need some help in order to fix this table. Recently we had wifi installed and during the installation the table was moved and the leg broke off. The table is an inch thick of solid wood. I’ve thought about using a fastener to act as a replacement but haven’t found a suitable replacement.


r/fixit • • 17h ago

Help with a snapped off torx bit in Stressless Recliner

Post image
2 Upvotes

I just bought a stressless recliner from a consignment store and went to take the backrest off so I could load it in my car when I found someone had snapped off a torx driver bit inside the left side backrest mounting bolt. It's in there very tight and flush with nothing to grab onto. Any ideas on the best way to get it out without damaging anything?

Update: I appreciate all the ideas. I tried a few but ultimately got it home by borrowing a friend's 4runner, so now I no longer have the time constraint and can drill it if need be


r/fixit • • 18h ago

fixed Lancia Ypsilon LX electric (2026) won't start — yellow triangle, red key, 3 chimes, blank screens — fixed with a 10-minute 12V battery disconnect

0 Upvotes

Hi everyone, sharing a startup fault I ran into on my 2026 Lancia Ypsilon LX electric (delivered February 2026, driven daily) and the reset procedure that got it running again in case it helps anyone else.

Symptoms

When pressing the start button, the car would not enter READY mode:

  • Both dashboard/infotainment screens stayed completely off.
  • Both the yellow triangle warning light and the red key warning light came on.
  • 3 audible chimes (beeps) sounded.

A similar glitch had happened once about a month earlier, but cycling the ignition off and on cleared it at the time. This time it stayed locked.

Checks Before Resetting

  1. Key fobs: Tested both the primary key and the spare key with no change.
  2. 12V auxiliary battery: Tested with a TOPDON BT100 battery analyzer, showing 12.60 V, 98% charge, 77% SoH, 4.86 mΩ internal resistance, and a "GOOD BATTERY" reading. So the 12V battery wasn't dead.

Temporary Fix (12V Hard Reset)

I disconnected a 12V battery terminal for about 10 minutes to let control unit capacitors drain and force a body/network reset, then reconnected it and tried starting again. After doing that, the car booted up and ran normally.

(Safety note: if working under the hood, stick strictly to the 12V auxiliary battery and avoid orange high-voltage cables/connectors.)

Current Status

I've opened a warranty service request with the dealer for a full fault-code scan and software/module check, and I'm keeping a proper wrench in the car in case it locks up again before the shop visit.

Has anyone seen this exact "3 chimes + red key + yellow triangle + blank screens" hang with a healthy 12V battery on Stellantis EVs or similar platforms? Any thoughts on what module usually causes this lockup?


r/fixit • • 18h ago

How to fix leaf blower broken case

Post image
1 Upvotes

I have a BillyGoat leaf blower where this screw area by the blower broke. Now it drags in the ground when pulled. I was hoping someone would advice of how to fix this? Thank you in advance!


r/fixit • • 19h ago

Samsung dryer

Post image
0 Upvotes

Any tips or is it done for?


r/fixit • • 20h ago

open Used hair spray to remove marker stains but made it worse. How do i fix this?

Post image
0 Upvotes

This wooden china cabinet is my MIL's and my daughter drew on it with permanent marker. Its been in the family for decades. I wiped marker off wood with hair spray before without issue. Now it looks awful. How do i fix this? Shes going to kill me.


r/fixit • • 20h ago

FAULTY RECLINERS

Thumbnail
gallery
1 Upvotes

Can anyone help me troubleshoot my power reclining sofa?

I have a three-seater reclining sofa from Raymour & Flanigan, and the warranty has expired. Both reclining seats are now stuck halfway. They only move back and forth about 8 inches.

When either seat reaches the point where it gets stuck, the light on the control button fades out. When I release the button, the light comes back on.

The problem started after I tipped the sofa over to vacuum underneath and remove things like bottle caps, pencils, and crayons. When I put it back upright, one seat would no longer return to its normal position. I thought the actuator was faulty, so I replaced it, but that did not fix the problem.

I then tipped the other seat over to look at how its mechanism worked. After that, it also became stuck in exactly the same position as the first seat.

Could tipping the sofa have shifted or jammed something? Is there a particular position the seats need to be in before tipping or returning the sofa upright? These are just my guesses, so I would appreciate advice from anyone who has experienced this or knows how to fix it.

The middle seat’s wooden frame and screws have also come apart, but I can handle that repair. I mainly need help getting the two reclining seats working again.

Any suggestions would be appreciated.

Here is the link showing light fading out https://photos.app.goo.gl/ChYi6Ezij454CRNo6

Thank you!


r/fixit • • 20h ago

open New kitchen faucet doesn't swivel

Thumbnail
gallery
1 Upvotes

Hello everyone,

I'm a complete beginner when it comes to DIY projects so please forgive me if my question is silly, but I cannot find an answer to it anywhere online.

I recently had to install a new kitchen faucet (M14450 ibergrif). After making sure the mounting nut was screwed in as tight as possible, I could no longer swivel the faucet left or right. I tried loosening it a little, which helped but now the entire tap also swivels whenever I turn the faucet.

I haven't found any advice that helped so far. Do you guys have any ideas as to what I am doing wrong? Pics are attached


r/fixit • • 21h ago

Tile is lifting!!

Thumbnail
gallery
23 Upvotes

Moved into a house in August, noticed the floors are cover in crappy cheap tiles. They are rising and have been that way since move in, no biggie truly I don’t care about them. But recently just read they could harbor phorid flies which I’ve been seeing 2-3 of near daily. Job for the landlord? Or something I can fix?


r/fixit • • 21h ago

Beko washer-dryer (5 yrs old) completely dead after violent spin – filter & cable OK, what next? Repair or replace?

1 Upvotes

Hi everyone,

I have a 5-year-old Beko washer-dryer combo (I never use the dryer function). During a spin cycle it started banging very hard (it was probably not well levelled), then the breaker tripped. Since then the machine is completely dead: no lights, no display, no reaction at all. The breaker no longer trips when I plug it back in.

What I've checked so far (always unplugged):

  • The wall socket works.
  • No water leak under or behind the machine.
  • Power cord and noise suppression filter tested with a multimeter: continuity is fine from the plug pins all the way to the output wires of the filter. No burn marks, no swelling on the filter.
  • I removed the top cover and the control panel. All connectors on the main board and the display board (ref. 2487801000) look properly seated, no visible burn marks. I unplugged and replugged them.
  • Motor control module ref. 2446407000 is at the bottom next to the filter. I didn't open it.
  • After reassembling and plugging it back in: still completely dead.

Some background: for a long time the machine would occasionally stop in the middle of a cycle, on and off, and I never found why. I've also opened it a few times in the past, and a few plastic clips on the front panel got slightly damaged.

My questions:

  1. What would be the most likely culprit now: the main/power board, the display board, or something else (door lock, a fuse on a board, a wiring harness damaged by the banging)?
  2. Is there anything else I can safely test myself with a multimeter before calling a technician?
  3. Is it worth repairing? A local repair service charges about €75 (call-out + diagnosis, repair bonus included) plus parts. Meanwhile, Black Friday deals for a basic washing machine are around €300–400. Given the history of random stops, would you repair or replace?

Thanks a lot for your help!