r/AskElectronics • • 6h ago

Why is IC hot?

Post image
4 Upvotes

I am trying out logic gate ICs, this is 74LS-86. I tried to build the full circuit, it did not work, but ic was hot, so I stripped it down to this, and it is still overheating. I wonder why?
This is the kit
https://amzn.eu/d/02skJtuB

I tried 5V and 3.3V too, with the same result


r/AskElectronics • • 17h ago

Why isn’t this astable NE555P timer circuit working?

Post image
0 Upvotes

I am a beginner, but i have made many such circuits before so i really don’t know what the problem could be.

The cap is 10uF and the resistor values are (top to bottom) 760ohm, 760oh, 270ohm.

I am powering it using ~5v from a battery

The potentiometer has continuity and i connected the wires to the pins properly.

The LEDs polarity is correct. The caps polarity is correct.


r/AskElectronics • • 12h ago

IPA did not clean my board, it made it worst

Post image
5 Upvotes

Hi,

I ordered couple of PCB from JLCPCB with matt black solder mask,
after soldering all the through hole components, i tried to clean it with IPA (99.99% alcohool) while scrubbing with ESD brush, but i noticed that the board get worst, i tried to apply again the IPA many time and scrub again, but it did not help.

the IPA is not supposed to get rid of the flux ? not sure if the mess is caused by the flux spreaded or because of the IPA it self.
may be i need to spray some alcohool on a bare PCB without any components soldered and see if i got the same effect ?!

for info i use for solder the 'Mechanic TY-V866 0.6mm 183°C Low-Temp/Melt'


r/AskElectronics • • 51m ago

Need Help Testing Motherboard Capacitors with a Multimeter

Thumbnail
gallery
0 Upvotes

Hi all,

I need some help with the readings I'm getting from the capacitors on my motherboard.

I've been investigating a fault on my motherboard to try to find out why it won't POST.

I've measured the resistance across 10 inductor coils (chokes) on the motherboard.

Most of them have resistance readings above 100 ohms, but one of the chokes located next to the 24-pin ATX power connector has a lower reading of just 11 ohms.

I suspect there may be a fault somewhere in that circuit, possibly involving a capacitor or another component, because I've noticed that the RAM voltage is lower than expected.

The RAM requires 1.5 V to work correctly, but I'm only getting 1.38 V.

I've compared the voltage readings with another fully working motherboard. The same choke on the working board measures 5V, whereas the one on my faulty motherboard measures only 0.78V.

This makes me suspect that something in the power supply circuit may be faulty and causing the voltage to drop.

I've tested 40 capacitors on the motherboard using my multimeter. Out of those, 27 gave resistance readings, while the remaining 13 displayed OL (over limit) instead of a numerical reading.

I've visually inspected all the capacitors, and none of them appear to be bulging, leaking or showing any obvious signs of damage.

I'm trying to understand whether these readings indicate that some of the capacitors may have failed.

Could anyone please explain how to test capacitors on a motherboard using a multimeter?

I'd particularly like to know:

How can I tell whether a capacitor is working correctly or has failed?
What does an OL reading mean when testing a capacitor in resistance mode?
How can I identify a shorted, open or faulty capacitor?
Can capacitors be tested accurately while they're still soldered onto the motherboard, or do they need to be removed?
Could a faulty capacitor or another component cause the voltage on an inductor coil to drop from 5 V to 0.78 V?

I'd really appreciate any advice on what measurements I should take next to help identify the fault.

Thanks in advance for your help!


r/AskElectronics • • 17h ago

74LS76AN JK flip flop behaving weird? Q' passes whatevers on K out regardless of the clock or J signals. PRE and CLR pulled high, clock manually swapped between high and low.

Post image
0 Upvotes

r/AskElectronics • • 21h ago

Help please with old control board from a 30 year old book

Thumbnail
gallery
1 Upvotes

Idk if this is the right sub but I’m looking for some help with fixing this if possible for my kid. It came from a book that I had as a kid. When the button was pressed the red LEDs would flash and a groaning roaring noise would come from the speaker.
The battery terminal on left (negative side) is mia and the wire that connected it to the circuit board is gone.

Is it fixable, and if so, how?

Fyi:
I know almost nothing about circuits or small electronics like this.


r/AskElectronics • • 4h ago

Need help identifying this component

Thumbnail
gallery
1 Upvotes

Portable record player showing a fault light and no power. Found this burnt out component. Need help identifying for replacement


r/AskElectronics • • 10h ago

Why does the flame in a soldering iron come out sideways?

Thumbnail
gallery
116 Upvotes

I'm a new user, please tell me if this is usable.


r/AskElectronics • • 21h ago

Significance of MLCC class 2 piezoelectric noise?

6 Upvotes

In terms of mechanical disturbances inducing electric noise, how bad is it if, for example, they are used to decouple an op amp in an audio circuit, or if they are outright in the audio circuit itself, for example coupling? I'd assume power supply rejection would do a lot to mitigate the noise in the first case, but what about the second?

Bonus question: if fairly high capacitance was needed for audio coupling (>100uF), and class 2 ceramics (for example, Samsung has 100uF for about 10 cents) were out of the question because of the noise, would electrolyrics be the only good pick in terms of cost for capacitance?


r/AskElectronics • • 12h ago

Is soldering a shared ground line on the underside of a perfboard good practice?​

Thumbnail
gallery
3 Upvotes

​Hi everyone,

​I'm new to soldering on perfboards/protoboards (until now, I've only used Arduino breadboards). I'm currently wiring up a small circuit with tactile pushbuttons and LEDs.

​To keep the top side looking clean and reduce wire clutter, I decided to create a common ground rail on the underside of the board by bridging/soldering the ground connections together, and I plan to route the remaining signal/power wires normally.

​Is this a valid and reliable technique on perfboards, or are there downsides I should watch out for (like short circuits or cold joints)? I've attached photos showing the top side with wires, the board without wires, and the underside soldering.

​(P.S. Apologies for the messy solder joints—this is my very first time soldering!)


r/AskElectronics • • 16h ago

Generating 10mv 100khz signal with ESP32

4 Upvotes

Hi friends, I built an analog filter and I wanted to generate a 10mv 100khz signal to test my amplification and attenuation, is this possible with an ESP32, I dont have a testbench. Thanks!