r/AskElectronics • • 11h ago

Why does the flame in a soldering iron come out sideways?

Thumbnail
gallery
126 Upvotes

I'm a new user, please tell me if this is usable.


r/AskElectronics • • 21h ago

Significance of MLCC class 2 piezoelectric noise?

6 Upvotes

In terms of mechanical disturbances inducing electric noise, how bad is it if, for example, they are used to decouple an op amp in an audio circuit, or if they are outright in the audio circuit itself, for example coupling? I'd assume power supply rejection would do a lot to mitigate the noise in the first case, but what about the second?

Bonus question: if fairly high capacitance was needed for audio coupling (>100uF), and class 2 ceramics (for example, Samsung has 100uF for about 10 cents) were out of the question because of the noise, would electrolyrics be the only good pick in terms of cost for capacitance?


r/AskElectronics • • 6h ago

Why is IC hot?

Post image
5 Upvotes

I am trying out logic gate ICs, this is 74LS-86. I tried to build the full circuit, it did not work, but ic was hot, so I stripped it down to this, and it is still overheating. I wonder why?
This is the kit
https://amzn.eu/d/02skJtuB

I tried 5V and 3.3V too, with the same result


r/AskElectronics • • 12h ago

IPA did not clean my board, it made it worst

Post image
5 Upvotes

Hi,

I ordered couple of PCB from JLCPCB with matt black solder mask,
after soldering all the through hole components, i tried to clean it with IPA (99.99% alcohool) while scrubbing with ESD brush, but i noticed that the board get worst, i tried to apply again the IPA many time and scrub again, but it did not help.

the IPA is not supposed to get rid of the flux ? not sure if the mess is caused by the flux spreaded or because of the IPA it self.
may be i need to spray some alcohool on a bare PCB without any components soldered and see if i got the same effect ?!

for info i use for solder the 'Mechanic TY-V866 0.6mm 183°C Low-Temp/Melt'


r/AskElectronics • • 16h ago

Generating 10mv 100khz signal with ESP32

4 Upvotes

Hi friends, I built an analog filter and I wanted to generate a 10mv 100khz signal to test my amplification and attenuation, is this possible with an ESP32, I dont have a testbench. Thanks!


r/AskElectronics • • 12h ago

Is soldering a shared ground line on the underside of a perfboard good practice?​

Thumbnail
gallery
3 Upvotes

​Hi everyone,

​I'm new to soldering on perfboards/protoboards (until now, I've only used Arduino breadboards). I'm currently wiring up a small circuit with tactile pushbuttons and LEDs.

​To keep the top side looking clean and reduce wire clutter, I decided to create a common ground rail on the underside of the board by bridging/soldering the ground connections together, and I plan to route the remaining signal/power wires normally.

​Is this a valid and reliable technique on perfboards, or are there downsides I should watch out for (like short circuits or cold joints)? I've attached photos showing the top side with wires, the board without wires, and the underside soldering.

​(P.S. Apologies for the messy solder joints—this is my very first time soldering!)


r/AskElectronics • • 21h ago

Is the KA3305P good?

3 Upvotes

Hi!

I'm buying my first power supply.

Is the Korad KA3305P good? I can find it for 200 euros in EU, I think the other choice would be the Siglent SPD3303C but it is 100 euros more expensive.

I don't plan to have the need for mV precision or high power usage.

Thanks!


r/AskElectronics • • 43m ago

I want to make a guitar effects processor using esp32 and have a question about 6.35mm jack connections

1 Upvotes

I am going to use wires, not a pcb, but i have no idea as to how to connect the properly. I know that i will need to add components in-between esp32 and input/output, but have absolutely no idea as to what and where.

To be clear I am going to make it use lv2 sound plugins, just like guitarix does, so that i have a portable preamp with the same settings as my pc setup.


r/AskElectronics • • 3h ago

IEPE + level shifter - I have doubts about a reference circuit design

1 Upvotes

Good morning!

I am reading up on a ADCs, specifically sound & vibration 24-bit ΣΔ ADCs like the Analog Devices AD7768-4 or the Texas Instruments ADS127L14, and have ben learning a lot, but there's a point that I can't seem to understand fully.

In the evaluation board for the AD7768-4, the EVAL-CN0582-USBZ, it shows a reference design for a 4-channel board with IEPE capabilities for the sensors and a freq response that starts at DC.

IEPE is normally used with accelerometers, and it's a system that sends a DC current to the sensors, and you measure the voltage change (around the bias voltage of ~12V). Usually, you do this by just filtering out the DC via a series capacitor (or sometimes a more complex filter).

But I can't fully understand how the CN0582 would have DC measuring capabilities while also having IEPE. I understand that they're using a level shifter to offset the bias voltage caused by IEPE, but I still don't get it.

Since this is a 24-bit ADC, every single source of noise would be a very big inaccuracy, so wouldn't any single imperfection in the current consumption of a sensor or the IEPE part of the circuit add a lot of noise, since it's directly in the signal chain? If the bias voltage changes because of sensor+cables current needs, wouldn't that be seen directly in the measurement result? Is a level shifter enough, is the IEPE voltage THAT stable?

Or is there something being done that I don't really get, like using a part of the IEPE circuit as feedback? (I don't see any part of the circuit doing this)


r/AskElectronics • • 4h ago

Need help identifying this component

Thumbnail
gallery
1 Upvotes

Portable record player showing a fault light and no power. Found this burnt out component. Need help identifying for replacement


r/AskElectronics • • 6h ago

Help with powering led upon condition

Post image
1 Upvotes

Hello,

I'm very new when it comes to electronics but I've some (little) skills regarding arduino.

I'm trying to create a toy to count to 10. The first idea was to use a arduino but I realized it might be done without it.

The main idea of the project is solving addition by only giving a part, such as "x + 1 = 10" or "1 + x = 10".

To make it visual for kids, I'll try to have to button sliding (like an elevator), one of the left, one the right. There will be wires for each pair that makes 10 (L1 -> R9, L2 -> R8, etc)

When the button is pressed, it lights a led. When the two (left and right) are in good position (see the pink wire), and pushed (simple on/off), it should light a third led to say "Left + Right = 10".

I tried to think on how to power this third led only when the sum is 10.

Here is little scheme (paint skill!) to explain the idea.

IA hinted me to use "NPN transistor", but I'm not good yet to understood clearly if it's a good solution or not.

Any help welcome


r/AskElectronics • • 18h ago

Omron E6B2 Encoder + External Power Supply: why did I fry my Arduino UNO?

Thumbnail
gallery
1 Upvotes

I have a Chinese Omron E6B2-CWZ6C NPN open-collector rotary encoder. Although the datasheet specifies a supply voltage range of 5–24 VDC, in reality, the encoder only starts working at around 5.5 V. So I uesed an external 5.5 V power supply connected to the brown (+) and blue (GND) wires, with pull-up resistors (2k Ohm) on the A (black), B (white), and Z (orange) signal outputs.

When measuring the signals with an oscilloscope (no arduino connected and manually rotating the encoder), I get a square wave ranging from 0 V to approximately 3.5 V (the probe/measurement points are indicated by the red circles in the tinkercad image near the resistence).
However, when I connected the outputs to Arduino pins D2 (A), D3 (B), and D4 (Z), I measured up to 10 V. I assumed the voltage was higher because the power supply and the Arduino did not share a common ground. I decided to connect the Arduino GND to the power supply GND, which ended up frying my Arduino ...

How can I interface the Omron encoder with an Arduino using an external power supply? And why did I fry my Arduino?

I'm a beginner any help would be greatly appreciated


r/AskElectronics • • 19h ago

Should I use isopropyl to clean my terminal?

1 Upvotes

I just need to know if it's safe to clean my + terminal, which is a small brass pin that was glued onto a plastic cap (assuming a layer of glue is causing the problem), with isopropyl or not. Before, it worked fine when the batteries made contact with the poles, but now when testing it just emits small amounts of sparks.


r/AskElectronics • • 20h ago

LC filter design inductor choice

1 Upvotes

I ended up designing a filter for audio using filter design software and simulated with some variations of parasitics, but am a bit unsuccessful in finding info on choosing the inductor. I have a few questions:

  1. I've figured out that inductors labeled for power applications, or bigger inductors have low series resistance for hundreds of microhenries valued inductors. Generally speaking, is there any disadvantage to these in such an application, besides size/cost?
  2. Would these inductors pick up noise due to any changing magnetic field in the vicinity? I realized while typing this that I am a bit unknowledgable about this component, but would something like a computer, its psu or digital side, emit emi that these inductors can pick up? How important is it to have shielding in that case

Thanks in advance for any answers


r/AskElectronics • • 21h ago

Help please with old control board from a 30 year old book

Thumbnail
gallery
1 Upvotes

Idk if this is the right sub but I’m looking for some help with fixing this if possible for my kid. It came from a book that I had as a kid. When the button was pressed the red LEDs would flash and a groaning roaring noise would come from the speaker.
The battery terminal on left (negative side) is mia and the wire that connected it to the circuit board is gone.

Is it fixable, and if so, how?

Fyi:
I know almost nothing about circuits or small electronics like this.


r/AskElectronics • • 17h ago

74LS76AN JK flip flop behaving weird? Q' passes whatevers on K out regardless of the clock or J signals. PRE and CLR pulled high, clock manually swapped between high and low.

Post image
0 Upvotes