r/AskElectronics • • 16h ago

Why does the flame in a soldering iron come out sideways?

Thumbnail
gallery
303 Upvotes

I'm a new user, please tell me if this is usable.


r/AskElectronics • • 3h ago

Got a Double side PCB doesn't have PTH, and I need them .

Thumbnail
gallery
6 Upvotes

I got 25 non PTH PCB made today, Now I am facing the issue with the Signal (Wrong assumes were made) Is there any fix.

The 4 pin hold the oled and I need the signal to travel both side.

I am kinda of realising (While typing) that the single side could have done it.


r/AskElectronics • • 4h ago

How to build this CW oscillator in LTspice

Thumbnail
gallery
6 Upvotes

I tried for the last 4 hours to model a crystal in LTspice and make this circuit work but it just won't oscillate. The schematic is from a 70's book and I cant use the old transistor but I dont think thats the problem. Basically the author said to choose the LC tank circuit according to the crystal frequency and those were really the instructions lol, ofc I tried to mess up with the other components but to no avail. The crystal I trying to model is one that I can buy where I am.

I've also tried to place some load capacitance to add up to the 30pF in the datasheet and still no oscillation. The frequency I'm trying to use is around 7.02MHz.

The transistor is getting a steady Vb=1.7V, Vc=9V and Ve=1V according to my simulation.

Any help is good.✌


r/AskElectronics • • 1d ago

Which one of those pins is Pin 1 on a STM32H503?

Post image
197 Upvotes

There are two dots, I'm assuming that the little one indicates pin 1. But I'm not sure. Can someone confirm if that's indeed pin 1 or not, please?


r/AskElectronics • • 1h ago

Desoldering a joystick/potentiometer from a motherboard

Thumbnail
gallery
2 Upvotes

Images attached. I'm pretty new to all of this stuff, but I wanted to replace the whole joystick of my PS5 Controller motherboard. I tried desoldering and pulling gently, but nothing comes off and I dont want to yank something important out accidently. I'm using a soldering iron, desoldering wick, and some solder for all of this.


r/AskElectronics • • 2h ago

Where can I find such switch brackets

Post image
2 Upvotes

Those are the switches (driver side) for my car windows, one window didn't close anymore. Instead of paying 75€ for a whole new switch, I'm thinking about to just replace those brackets. Any help is welcome!


r/AskElectronics • • 12h ago

Why is IC hot?

Post image
9 Upvotes

I am trying out logic gate ICs, this is 74LS-86. I tried to build the full circuit, it did not work, but ic was hot, so I stripped it down to this, and it is still overheating. I wonder why?
This is the kit
https://amzn.eu/d/02skJtuB

I tried 5V and 3.3V too, with the same result


r/AskElectronics • • 18h ago

IPA did not clean my board, it made it worst

Post image
26 Upvotes

Hi,

I ordered couple of PCB from JLCPCB with matt black solder mask,
after soldering all the through hole components, i tried to clean it with IPA (99.99% alcohool) while scrubbing with ESD brush, but i noticed that the board get worst, i tried to apply again the IPA many time and scrub again, but it did not help.

the IPA is not supposed to get rid of the flux ? not sure if the mess is caused by the flux spreaded or because of the IPA it self.
may be i need to spray some alcohool on a bare PCB without any components soldered and see if i got the same effect ?!

for info i use for solder the 'Mechanic TY-V866 0.6mm 183°C Low-Temp/Melt'


r/AskElectronics • • 29m ago

How to adjust voltage?

Post image
0 Upvotes

I built this psu years ago and it's been working fine. I want to rebuild it with a new transformer though. Last time I used a random ancient 270v output transformer and a seperate 9v. I can't get the proper transformer but I have found one with 270v and 14v. How can I get the voltages back to where they should be? There is a couple of things I don't understand. Why did they add 40v to the 9v? This part of the circuit powers valve heaters at 6.3v, but why not use 6.3v-0v instead of 46.3v-40v? Ignoring that though, to get the output back to where it should be would changing r2 and r3 to add 35v instead of 40v work? Although I seem to be able to build a circuit from a schematic, altering the design is beyond my skills. This is the only image of the schematic I can find, but it's just readable.


r/AskElectronics • • 1h ago

Asus VG248QE monitor turns on white

Thumbnail
gallery
1 Upvotes

Trying to figure out what's wrong with my monitor but I have no idea where to look? It turns on white and then goes to sleep. No Asus logo. Anyone have any experience fixing these? I found both sides of this C47 capacitor to be shorted and removing it didn't follow the capacitor. I don't have a diagram to know if that's normal or not? Also this D10F2 is a diode or fuse? I feel like I should be looking for a fuse but don't know where one is?


r/AskElectronics • • 11h ago

Can I 'Hotwire' a 10k Ohm potentiometer without damaging the circuit

Post image
6 Upvotes

Total electronics noob here. I'm trying to repair this old Korg LP350 Grand Piano to give away in charity. The sound output has gradually decreased overtime, now I can barely hear it.

I suspect the volume slider ( a 10K Ohm sliding potentiometer, as suggested by Claude, and I checked online it looks same) , is broken, since the sound crackles when I slide it.

Question is, can I 'hotwire' the pins, the red and white ones, without damaging the circuit, so I can diagnose if this part is the problem. If yes, which wires should I be connecting? I can upload more data if needed

Thanks in Advance


r/AskElectronics • • 5h ago

Where do I start to design a Bluetooth to LTE-M gateway?

2 Upvotes

I’m trying to create a gateway to relay unpredictable but small amounts of data from BLE devices, immediately over LTE-M to a backend server.

I don’t want this gateway to poll the devices. The devices will advertise when they need to send the data, and the gateway will be scanning for those advertisements pretty regularly, so that the data can be sent within 5 seconds.

The data sent is about 30 bytes plus any encryption (currently using TLS over Wi-Fi so the data is quite a bit more over Wi-Fi). This can occur once an hour or up to 15 times an hour. Some of those occurrences are non-urgent but others are required to be delivered asap.

The gateway will pass this data on to my backend or MQTT. It is possible that the backend needs to send a 30 byte response back, and the gateway will have to deliver to the devices (which will wait for a response until they timeout).

Expected daily traffic would average around 400-600 bytes to the backend, before any overhead for encryption, and predominantly only an acknowledgement or result code back from the backend.

Ideally, these BLE devices could even get OTA updates too, but that part could be handled differently.

My goals are:

- quick transfer of the data from devices to the backend
- keep the landed cost under $30
- keep the data costs under $1 a month (500 bytes per day or 15 kbytes per month plus overhead)
- easy US coverage and ideally good global coverage in as many regions as possible
- ideally zero configuration

My current research tells me that one path would be to have a Nordic nRF52840, doing the BLE communication and most of the hard work, interfacing with a Nordic nRF9151 or Quectel EG916Q, to take AT commands and send and receive data.

Am I on the right track?

I’ve got some experience writing BLE code as I’ve already written the code to allow the devices to communicate with iOS and Android apps and pass the same data to the backed over TLS. It works well but now I want to remove the smartphones from the equation. I have no experience with LTE-M or NB-IoT.

I understand that a big hurdle will be to get carriers to allow this device to use their network. And that I will have to pay significant fees to get this device certified not just by FCC but also the carriers. I’d love to hear more about this.

If you’ve got some experience with LTE-M gateways and devices, please tell me where I can read up more about this and how to select my MCU and cellular module.

Right now I don’t have a budget but once I can narrow down the viable paths, i will know enough to create a budget and allocate funding.

Thanks!


r/AskElectronics • • 5h ago

Wireless Mouse repair troubleshoot (metal pins)

Post image
2 Upvotes

Hi cleaning my rapoo vt9 wireless mouse out. I am reassembling it, but I don’t where this pins go back in or how they sit in the mouse? What are these for or how do they connect? Someone said for the Mark 1 connector but idk how that connects?


r/AskElectronics • • 14h ago

Are the white clips safe to remove?

Thumbnail
gallery
10 Upvotes

I opened up an onn 20 inch soundbar to take the drivers and use them on a different speaker enclosure but when i got everything open i saw the capacitor size and all the other components and don’t know if its safe to continue considering capacitors store energy even after the system is powered off (or so i heard). Theres 3 white clips total and to get them out id have to be close to all the components since the speakers top cant be removed and only the front gives access to everything. Capacitor says 68 uf and this is a wall outlet powered speaker


r/AskElectronics • • 2h ago

Repairing W58814 car radio, no sound

Thumbnail elektrotanya.com
1 Upvotes

I have car radio from 2005 Toyota and I'm trying to fix it just for fun and trying study something new. Radio model is W58814.

It first sometimes lost sound and then it came back. Sometimes when audio came back it was very loud and you cant control it. Now it has been without sound almoust half year. Everything else works fine in the radio. Just no sound.

What I have tested at this point:

-Using FM radio or CD

-Measuring all speakers. Got 3-8 ohm and no short to ground.

-There is typical problem with main power transistors and I have resoldered them and measured them. To me they work fine but somereason Q703 and Q723 transistors which transform 10V to 5V are very hot even radio is just power on and idling. Is this normal?

-I changed IC amplifier IC231 because it was very hot also if you just power up radio.

-I tryed to measure after IC amplifier between FL + and - (pins what supply speaker) but it was 0V. Infact I'm not sure what I should get if I measure between those pins. I measured using VAC with multimeter. But I also tryed to use VDC and no voltage difference between amplifier pins. But if I measure between for example FL + and radio body I get ~3VDC. But if I have understand right, it should be VAC side what I need to use when I measure speaker output.

I have to admit that I dont have no glue where to test next. If someone have any ideas how to procees I would be thankful. My guts are telling the fault shouldnt be big :)

I find manual here and it have also pcb diagram https://elektrotanya.com/panasonic_matsushita_cq-ts7421k_toyota.pdf/download.html#dl


r/AskElectronics • • 21h ago

[first handheld dmm] Brymen BM869s or uni-t ut181a

Post image
32 Upvotes

hello everyone,

i am about to buy my first pro dmm. in specific i need a handheld dmm for mobility, common household stuff, dead pcb's, smartphone, tablet and daily electronics repair.

do you have experience with one of these handheld multimeter and which one would you buy as a first professional handheld digital multimeter and why? is there something i have to have in mind when buying one?

are there maybe other better options for a first device?

i would appreciate your opinion. thank you in advance.


r/AskElectronics • • 5h ago

Dualsense ps5 help with jumper

Post image
0 Upvotes

Hi everyone, before reading please know that I used google translate to help me write because english is not my mothertongue.

While desoldering the old potentiometer, I accidentally pulled off the solder pad. I have other working DualSense controllers, so I don't strictly need to get this one working, but I thought I'd use this as an opportunity to learn something useful.

I really don't know much about this topic. I did some research online and I think I understood that it can still be fixed using a "jumper wire". However, I'm struggling to understand how to do it. I know I need a copper wire, but I don't understand where I'm supposed to run it to from the pin.

Also, I don't understand why the solder won't stick, even when using flux.

I'm a beginner and I'd like to learn more for the future.


r/AskElectronics • • 9h ago

Need help identifying this component

Thumbnail
gallery
2 Upvotes

Portable record player showing a fault light and no power. Found this burnt out component. Need help identifying for replacement


r/AskElectronics • • 6h ago

I want to make a guitar effects processor using esp32 and have a question about 6.35mm jack connections

1 Upvotes

I am going to use wires, not a pcb, but i have no idea as to how to connect the properly. I know that i will need to add components in-between esp32 and input/output, but have absolutely no idea as to what and where.

To be clear I am going to make it use lv2 sound plugins, just like guitarix does, so that i have a portable preamp with the same settings as my pc setup.


r/AskElectronics • • 6h ago

Need Help Testing Motherboard Capacitors with a Multimeter

Thumbnail
gallery
1 Upvotes

Hi all,

I need some help with the readings I'm getting from the capacitors on my motherboard.

I've been investigating a fault on my motherboard to try to find out why it won't POST.

I've measured the resistance across 10 inductor coils (chokes) on the motherboard.

Most of them have resistance readings above 100 ohms, but one of the chokes located next to the 24-pin ATX power connector has a lower reading of just 11 ohms.

I suspect there may be a fault somewhere in that circuit, possibly involving a capacitor or another component, because I've noticed that the RAM voltage is lower than expected.

The RAM requires 1.5 V to work correctly, but I'm only getting 1.38 V.

I've compared the voltage readings with another fully working motherboard. The same choke on the working board measures 5V, whereas the one on my faulty motherboard measures only 0.78V.

This makes me suspect that something in the power supply circuit may be faulty and causing the voltage to drop.

I've tested 40 capacitors on the motherboard using my multimeter. Out of those, 27 gave resistance readings, while the remaining 13 displayed OL (over limit) instead of a numerical reading.

I've visually inspected all the capacitors, and none of them appear to be bulging, leaking or showing any obvious signs of damage.

I'm trying to understand whether these readings indicate that some of the capacitors may have failed.

Could anyone please explain how to test capacitors on a motherboard using a multimeter?

I'd particularly like to know:

How can I tell whether a capacitor is working correctly or has failed?
What does an OL reading mean when testing a capacitor in resistance mode?
How can I identify a shorted, open or faulty capacitor?
Can capacitors be tested accurately while they're still soldered onto the motherboard, or do they need to be removed?
Could a faulty capacitor or another component cause the voltage on an inductor coil to drop from 5 V to 0.78 V?

I'd really appreciate any advice on what measurements I should take next to help identify the fault.

Thanks in advance for your help!


r/AskElectronics • • 9h ago

IEPE + level shifter - I have doubts about a reference circuit design

0 Upvotes

Good morning!

I am reading up on a ADCs, specifically sound & vibration 24-bit ΣΔ ADCs like the Analog Devices AD7768-4 or the Texas Instruments ADS127L14, and have ben learning a lot, but there's a point that I can't seem to understand fully.

In the evaluation board for the AD7768-4, the EVAL-CN0582-USBZ, it shows a reference design for a 4-channel board with IEPE capabilities for the sensors and a freq response that starts at DC.

IEPE is normally used with accelerometers, and it's a system that sends a DC current to the sensors, and you measure the voltage change (around the bias voltage of ~12V). Usually, you do this by just filtering out the DC via a series capacitor (or sometimes a more complex filter).

But I can't fully understand how the CN0582 would have DC measuring capabilities while also having IEPE. I understand that they're using a level shifter to offset the bias voltage caused by IEPE, but I still don't get it.

Since this is a 24-bit ADC, every single source of noise would be a very big inaccuracy, so wouldn't any single imperfection in the current consumption of a sensor or the IEPE part of the circuit add a lot of noise, since it's directly in the signal chain? If the bias voltage changes because of sensor+cables current needs, wouldn't that be seen directly in the measurement result? Is a level shifter enough, is the IEPE voltage THAT stable?

Or is there something being done that I don't really get, like using a part of the IEPE circuit as feedback? (I don't see any part of the circuit doing this)


r/AskElectronics • • 18h ago

Is soldering a shared ground line on the underside of a perfboard good practice?​

Thumbnail
gallery
5 Upvotes

​Hi everyone,

​I'm new to soldering on perfboards/protoboards (until now, I've only used Arduino breadboards). I'm currently wiring up a small circuit with tactile pushbuttons and LEDs.

​To keep the top side looking clean and reduce wire clutter, I decided to create a common ground rail on the underside of the board by bridging/soldering the ground connections together, and I plan to route the remaining signal/power wires normally.

​Is this a valid and reliable technique on perfboards, or are there downsides I should watch out for (like short circuits or cold joints)? I've attached photos showing the top side with wires, the board without wires, and the underside soldering.

​(P.S. Apologies for the messy solder joints—this is my very first time soldering!)


r/AskElectronics • • 11h ago

Help with powering led upon condition

Post image
1 Upvotes

Hello,

I'm very new when it comes to electronics but I've some (little) skills regarding arduino.

I'm trying to create a toy to count to 10. The first idea was to use a arduino but I realized it might be done without it.

The main idea of the project is solving addition by only giving a part, such as "x + 1 = 10" or "1 + x = 10".

To make it visual for kids, I'll try to have to button sliding (like an elevator), one of the left, one the right. There will be wires for each pair that makes 10 (L1 -> R9, L2 -> R8, etc)

When the button is pressed, it lights a led. When the two (left and right) are in good position (see the pink wire), and pushed (simple on/off), it should light a third led to say "Left + Right = 10".

I tried to think on how to power this third led only when the sum is 10.

Here is little scheme (paint skill!) to explain the idea.

IA hinted me to use "NPN transistor", but I'm not good yet to understood clearly if it's a good solution or not.

Any help welcome


r/AskElectronics • • 22h ago

Generating 10mv 100khz signal with ESP32

4 Upvotes

Hi friends, I built an analog filter and I wanted to generate a 10mv 100khz signal to test my amplification and attenuation, is this possible with an ESP32, I dont have a testbench. Thanks!