r/TpLink • • 55m ago

TP-Link - General I'm disappointed

1 Upvotes

So I am a proud owner of many TP-Link devices, especially routers. So I have an Archer AX58, and I couldn't find the Wifi mode settings in the web interface, only in the tether app!?

So I needed to change my wifi mode from n/ax to just n on 2.4 gigs, and then turn it back on. I tried to search for it in the whole web interface, but I haven't found it after a deep search. I thought I was going insane, like literally insane. Then I decided to check the Tether app, ofc it was there. But the main point here is that tp-link is moving many things to the tether app, even though they aren't on the web, and I am actually standing up for the people, who don't manage or don't use that app much, and trying to change some non-existent thingies. Many people still don't use the apps, for example on my Archer C20, C6, the app is almost useless, it has basic things. I see, the Tether app is a nice idea, but if you are building it, also add the things to the web interface, even the small ones.

tl;dr: tp link is forgetting about things to add to the web interface, whilst adding it to their app. user complaining for it, that some people still dont use the app, or is useless for some things


r/TpLink • • 2h ago

TP-Link - Technical Support Archer Ge800 does not do the speed of my connection.

1 Upvotes

I have fios 2gig internet. My pc is connected(cat6e) to the 10 gig port and I do not get the speed of 2 gigs when doing a speed test. When my fios router is hooked up I do get the speed. Does anyone know of there is a setting I can change?


r/TpLink • • 3h ago

TP-Link - Technical Support TP-Link RE360 V1 (EU) bricked after firmware update

3 Upvotes

My RE360 V1 (EU) stopped working right after a firmware update. On power-up all LEDs (Ethernet, 2.4G, 5G, Power) light up briefly, then the WPS ring glows purple for a few seconds, then only the Power LED stays on. Nothing else happens.

  • Ethernet LED stays off even with a cable connected to a PC
  • Web interface unreachable (static IP, tried 192.168.0.254)
  • Reset button does nothing
  • TFTP recovery doesn't work either

Has anyone managed to fix an RE360 (or similar TP-Link extender) in this state? Any tips appreciated.

Thanks!


r/TpLink • • 4h ago

TP-Link - Technical Support EAP225 going to Isolated status after 5.3.1 update

Thumbnail reddit.com
1 Upvotes

Cross posted from Omada


r/TpLink • • 5h ago

TP-Link - Technical Support My TpLink has been acting up for a week now

1 Upvotes

Surprisingly this Sunday and the past Sunday, cause I want to stream and I can't because it keeps reseting by itself and making this very annoying high pitch noise everytime it turns off. I have the TP-Link TL-WPA4220 KIT AV600. I'm attaching what's been happening and the sound it makes. I appreciate anyone even looking at it, cause this is honestly annoying me.


r/TpLink • • 7h ago

TP-Link - General Any advice?

0 Upvotes

I have been struggling for DAYS now to get my wifi working on the other half of my house. I have an HB810 router, and just got a be3600 extender. Person that lives on the other half of the house is getting poor connection even with the extender. I have it in AP mode and wired to my router. Why do I have 2 extra networks with _ext? How can I just combine the into the normal router channel? Do I even want ap mode? I feel like I keep finding conflicting information.


r/TpLink • • 10h ago

TP-Link - Technical Support Xbox and deco network

1 Upvotes

Hi. I have a deco network with att 1g. I have three nodes in ap mode. I have an Xbox in the bedroom and one in the living room. One is wired into a node and the other wireless. However, both have strict NAT types. I’ve looked into how to fix it with the port switching or something but it’s so foreign to me lol. Anybody have any help? Thanks in advance!


r/TpLink • • 10h ago

TP-Link - Technical Support HELP

Post image
2 Upvotes

I have this archer c54 for 3 years already. At first, it runs smoothly but recently it keeps disconnecting me and showing this red light on internet icon. But when I restarted it, it foes back to normal again even after customizing wifi name and password but after a few hours or days, it comes back like this again where i need to restart again and change wifi name and password. What do I do to stop this cycle?


r/TpLink • • 13h ago

TP-Link - General Wifi verbeteren op eerste verdieping nieuwbouwwoning

Thumbnail reddit.com
1 Upvotes

r/TpLink • • 15h ago

TP-Link - Technical Support Can't log into Control Panel on browser.

Post image
0 Upvotes

Hello, I picked up this TP-Link TL-WR841N off of Ebay and upon arrival it would not let me log in to the control panel on the browser. I tried factory resetting it by holding the button on the back but typing admin for the username and password still won't work, any ideas on what I should do?


r/TpLink • • 17h ago

TP-Link - General Wired vs wireless Backhaul

7 Upvotes

I bought a TP-Link Deco BE65, but had a question for all of you.

I have the setup for both satellite WAP's to be wired but using Cat 5E. Would it be better for me to set them up with a wireless backhaul, or is the Cat 5E going to give better throughput across the mesh?


r/TpLink • • 20h ago

TP-Link - Technical Support Devices on XE75 Pro

1 Upvotes

I was using a M5 mesh with 5 hubs with a separate IoT network and everything had been working fine. The hardware was 6 years old, so I upgraded to XE75 Pro 3 pack.

Now everyday my smart devices - plugs, dyson and Raspberry pi loose connectivity everyday and need to be re - set up and in case of Pi I need to click connect each time.

This morning, Dyson is just refusing to connect to wifi even after multiple resets.

Has anyone experienced and / or resolved this?

Tried multiple things but I am starting to wonder if I bought a lemon..


r/TpLink • • 20h ago

TP-Link - Technical Support Bricked FR205

1 Upvotes

I have a Festa FR205 with a failed OpenWrt install. Now it displays the TP-Link recovery, but none of the images load successfully. There is a de-brick procedure, but I don't want to open it up and solder a connector.

I want to keep it, but I need someone to de-brick it for me. Any takers?

WHITE Festa FR205(UN) VER 1.6


r/TpLink • • 22h ago

TP-Link - Technical Support ethernet backhaul defective.

0 Upvotes

New Deco 7 Pro Tri-Band BE14000  not using 10g ethernet backhaul. I can't find any manual way to set this up. Are there any tricks I can try before I sent it back to Amazon? Thanks.


r/TpLink • • 23h ago

TP-Link - Technical Support Defective BE 1300 unit - common or bad luck?

0 Upvotes

After 2 weeks of troubleshooting with Gemini and Claude, I gave up, and here is the summary of my router (by Gemini):

On one specific satellite node (connected via wired Ethernet backhaul), the 6 GHz radio completely falls apart under load despite sitting right next to it with a great signal:

Signal: RSSI -48 to -53 dBm, Noise -92 dBm (~44 dB SNR)

Negotiation Collapse: Link rate drops to `8 Mbps` and stays hard-locked at MCS Index 1 (NSS 1)

Real-World Speed: Downlink/Uplink tank to 29–58 Mbps with massive loaded latency (1.49s / 40 RPM on `networkQuality`)

How I Isolated It: Same node, other bands:Wired Ethernet, 2.4 GHz, and 5 GHz (160 MHz) on this exact same unit work flawlessly—negotiating at `1441–1633 Mbps` (MCS 8) and pulling 840+ Mbps down (`1200+ RPM`, 0% packet loss).

Other nodes: The other two Deco units in the same 3-pack work completely fine on both 5 GHz and 6 GHz.

Multiple clients: Reproduces identically on both an M4 Pro MacBook Pro and a Windows 11 desktop with a Qualcomm FastConnect 7800 Wi-Fi 7 card.

What I Already Tried (No Permanent Fix):

  1. Verified all nodes are on the latest firmware
  2. Tested both 320 MHz and 160 MHz channel widths on 6 GHz
  3. Disabled QoS, MLO, Fast Roaming (802.11r), Beamforming, and IPv6
  4. Ran Network Optimization, rebooted, and did a full factory reset on the node

Has anyone else seen a single Deco BE13000 / BE67 unit develop a dead or degraded 6 GHz radio like this while 5 GHz stays rock solid?


r/TpLink • • 1d ago

TP-Link - Technical Support Archer TBE550E - slow download, fast upload

1 Upvotes

I have a 10 Gbps symmetric FTTH and bought Archer TBE550E for my pc.

I get extra slow download speed and ultra fast upload.

The shop refunded me without asking questions.

Any ideas what I'm doing wrong?

I had an Asus adapter earlier and I had 300-400 MBps in both directions, so it's not the PC

Edit: solved it with 2 steps and gemini 4. Seems there's a known bug on mediatek chips. Run this in powershell: Disable-NetAdapterRsc -Name "Wifi TP-Link"

And go to tp link Nordic page and take the latest driver of August 2026


r/TpLink • • 1d ago

TP-Link - Technical Support Deco BE63 5GHz Performance Question

0 Upvotes

I have had my BE63 set up (4 nodes) for several months now. I have a 1Gbps ISP connection. No issues on wired connection. I get near full speed. Wi-fi is not, but is been better in past. Wi-fi was both stable and great performance, across all bands until recently. Now:

6GHz - I used to consistently get 700 - 850Mbps. Now, my wife's laptop with Realtek Wi-fi still breaks the 700 Mbps mark. I have a Intel Wi-fi6E card in my desktop that gets about 550Mbps now...it used to be better. My Pixel 9 Pro phone set to Wifi7 gets over 800Mbps.

5GHz - I only get 400 - 550 Mbps, even when close to a node (including main router), and with Wi-fi 6 160Hz.

Is there some other setting I should check in the Deco app, or can you confirm what settings I should have enabled/disabled to see if that is affecting performance? I am on the latest firmware.


r/TpLink • • 1d ago

TP-Link - General Deco X20 as Unifi U6 Lite

Thumbnail github.com
1 Upvotes

r/TpLink • • 1d ago

TP-Link - General Nice addition to my TL-WR3602BE travel set

Post image
2 Upvotes

Just bought myself a travel router TL-WR3602BE to make setting up my holiday (public) Wifi setup a little bit easier and safer.

Planning to add my home Wifi network credentials so all devices automatically connect when on holiday.

Just got a nice addition to my Wifi travel kit from my wife, a travel pouch. So I can take the TL-WR3602BE with accessories 😅

Just a thing you expect to be included with specific travel equipment!


r/TpLink • • 2d ago

TP-Link - Technical Support BE11000 ethernet backhaul fails

0 Upvotes

I just got a replacement set if 3 decos and ethernet backhaul crashes network. The units work fine when all left to connect wirelessly. As soon as I connect the 2 satellites to the main deco the network fails. The tplink switch's lights start blinking rapidly, mybpc disconnects from the network [connected via ethernet] my s24 ultra losses wifi connection and speeds on laptop connected via ethernet drops. I've had many conversations with support which lead me to replace the previous be11100. There must be a solution here.


r/TpLink • • 2d ago

TP-Link - Technical Support CPE 510s for Christmas lighting controllers

0 Upvotes

I’ve spent way too many maddening hours on this already. Help.

I have a computer at 192.168.0.10 plugged into the wan side of a CPE510 that is acting as an access point, 0.1. I have 3 other CPE510 devices at 0.2-0.4, connected back to the access point as clients. I have 3 devices, each connected to a CPE510, with IPs 0.51-53.

From the computer, I can ping all the CPE510, but I cannot see the devices attached to them. I’m at my wits end as to why.

Any ideas? I can ping them connected to physical switch, but not across the CPEs.


r/TpLink • • 2d ago

TP-Link - Technical Support TP LINK ax3000 cannot add Nordvpn

1 Upvotes

I bought a tp link ax3000 router and I wanted to setup Nordvpn but when I go to advanced/vpn client I am unable to add anything can I assume this router does not support Nordvpn, firmware is up to date

Firmware Version: 1.2.2 Build 20260810 rel.19227(4341)

Hardware Version: Archer AX55 v4.0


r/TpLink • • 2d ago

TP-Link - Technical Support Deco Speeds slow down compared to ISP router

0 Upvotes

I'm trying to find a solution to this problem that I've been having. Sometimes my Deco network will just randomly slow down compared to the speeds I get when running speedtest connected directly to the router, even standing a couple of feet from the main Deco. I reboot the system and the speed goes back to normal but for some reason it goes right back down. I sometimes notice the Deco system disconnects (if I'm playing online at the time or something) and after that when it comes back on the speeds on the Deco network are down to about 1/3 or 1/2 of the router's speed. Anyone got any clues? I got 3 S4 models running on firmware version 1.6.2 Build 20240718 Rel. 69205


r/TpLink • • 2d ago

TP-Link - Technical Support tp link model TL-WN722N monitor mode

0 Upvotes

Español and English Post

https://easyosinstall.wordpress.com/2026/11/20/tp-link-wireless-modo-monitor/

Seguro que habéis buscado por internet y solo encontrais que este modelo de tp link TL-WN722N es imposible ponerlo en modo monitor.

PUes no es así, aquí os incluyo dos scripts para que lo cambiéis a modo monitor , capturéis paquetes y puedan hacer AUDITORIA DE SISTEMAS.