r/TpLink • • 14h ago

TP-Link - General Wired vs wireless Backhaul

7 Upvotes

I bought a TP-Link Deco BE65, but had a question for all of you.

I have the setup for both satellite WAP's to be wired but using Cat 5E. Would it be better for me to set them up with a wireless backhaul, or is the Cat 5E going to give better throughput across the mesh?


r/TpLink • • 7h ago

TP-Link - Technical Support HELP

Post image
2 Upvotes

I have this archer c54 for 3 years already. At first, it runs smoothly but recently it keeps disconnecting me and showing this red light on internet icon. But when I restarted it, it foes back to normal again even after customizing wifi name and password but after a few hours or days, it comes back like this again where i need to restart again and change wifi name and password. What do I do to stop this cycle?


r/TpLink • • 1h ago

TP-Link - Technical Support EAP225 going to Isolated status after 5.3.1 update

Thumbnail reddit.com
1 Upvotes

Cross posted from Omada


r/TpLink • • 2h ago

TP-Link - Technical Support My TpLink has been acting up for a week now

1 Upvotes

Surprisingly this Sunday and the past Sunday, cause I want to stream and I can't because it keeps reseting by itself and making this very annoying high pitch noise everytime it turns off. I have the TP-Link TL-WPA4220 KIT AV600. I'm attaching what's been happening and the sound it makes. I appreciate anyone even looking at it, cause this is honestly annoying me.


r/TpLink • • 7h ago

TP-Link - Technical Support Xbox and deco network

1 Upvotes

Hi. I have a deco network with att 1g. I have three nodes in ap mode. I have an Xbox in the bedroom and one in the living room. One is wired into a node and the other wireless. However, both have strict NAT types. I’ve looked into how to fix it with the port switching or something but it’s so foreign to me lol. Anybody have any help? Thanks in advance!


r/TpLink • • 10h ago

TP-Link - General Wifi verbeteren op eerste verdieping nieuwbouwwoning

Thumbnail reddit.com
1 Upvotes

r/TpLink • • 12h ago

TP-Link - Technical Support Can't log into Control Panel on browser.

Post image
1 Upvotes

Hello, I picked up this TP-Link TL-WR841N off of Ebay and upon arrival it would not let me log in to the control panel on the browser. I tried factory resetting it by holding the button on the back but typing admin for the username and password still won't work, any ideas on what I should do?


r/TpLink • • 17h ago

TP-Link - Technical Support Devices on XE75 Pro

1 Upvotes

I was using a M5 mesh with 5 hubs with a separate IoT network and everything had been working fine. The hardware was 6 years old, so I upgraded to XE75 Pro 3 pack.

Now everyday my smart devices - plugs, dyson and Raspberry pi loose connectivity everyday and need to be re - set up and in case of Pi I need to click connect each time.

This morning, Dyson is just refusing to connect to wifi even after multiple resets.

Has anyone experienced and / or resolved this?

Tried multiple things but I am starting to wonder if I bought a lemon..


r/TpLink • • 17h ago

TP-Link - Technical Support Bricked FR205

1 Upvotes

I have a Festa FR205 with a failed OpenWrt install. Now it displays the TP-Link recovery, but none of the images load successfully. There is a de-brick procedure, but I don't want to open it up and solder a connector.

I want to keep it, but I need someone to de-brick it for me. Any takers?

WHITE Festa FR205(UN) VER 1.6


r/TpLink • • 28m ago

TP-Link - Technical Support TP-Link RE360 V1 (EU) bricked after firmware update

0 Upvotes

My RE360 V1 (EU) stopped working right after a firmware update. On power-up all LEDs (Ethernet, 2.4G, 5G, Power) light up briefly, then the WPS ring glows purple for a few seconds, then only the Power LED stays on. Nothing else happens.

  • Ethernet LED stays off even with a cable connected to a PC
  • Web interface unreachable (static IP, tried 192.168.0.254)
  • Reset button does nothing
  • TFTP recovery doesn't work either

Has anyone managed to fix an RE360 (or similar TP-Link extender) in this state? Any tips appreciated.

Thanks!


r/TpLink • • 4h ago

TP-Link - General Any advice?

0 Upvotes

I have been struggling for DAYS now to get my wifi working on the other half of my house. I have an HB810 router, and just got a be3600 extender. Person that lives on the other half of the house is getting poor connection even with the extender. I have it in AP mode and wired to my router. Why do I have 2 extra networks with _ext? How can I just combine the into the normal router channel? Do I even want ap mode? I feel like I keep finding conflicting information.


r/TpLink • • 20h ago

TP-Link - Technical Support Defective BE 1300 unit - common or bad luck?

0 Upvotes

After 2 weeks of troubleshooting with Gemini and Claude, I gave up, and here is the summary of my router (by Gemini):

On one specific satellite node (connected via wired Ethernet backhaul), the 6 GHz radio completely falls apart under load despite sitting right next to it with a great signal:

Signal: RSSI -48 to -53 dBm, Noise -92 dBm (~44 dB SNR)

Negotiation Collapse: Link rate drops to `8 Mbps` and stays hard-locked at MCS Index 1 (NSS 1)

Real-World Speed: Downlink/Uplink tank to 29–58 Mbps with massive loaded latency (1.49s / 40 RPM on `networkQuality`)

How I Isolated It: Same node, other bands:Wired Ethernet, 2.4 GHz, and 5 GHz (160 MHz) on this exact same unit work flawlessly—negotiating at `1441–1633 Mbps` (MCS 8) and pulling 840+ Mbps down (`1200+ RPM`, 0% packet loss).

Other nodes: The other two Deco units in the same 3-pack work completely fine on both 5 GHz and 6 GHz.

Multiple clients: Reproduces identically on both an M4 Pro MacBook Pro and a Windows 11 desktop with a Qualcomm FastConnect 7800 Wi-Fi 7 card.

What I Already Tried (No Permanent Fix):

  1. Verified all nodes are on the latest firmware
  2. Tested both 320 MHz and 160 MHz channel widths on 6 GHz
  3. Disabled QoS, MLO, Fast Roaming (802.11r), Beamforming, and IPv6
  4. Ran Network Optimization, rebooted, and did a full factory reset on the node

Has anyone else seen a single Deco BE13000 / BE67 unit develop a dead or degraded 6 GHz radio like this while 5 GHz stays rock solid?