r/DIY • • 5d ago

weekly thread General Feedback/Getting Started Q&A [Weekly Thread]

9 Upvotes

General Feedback/Getting Started Q&A Thread

This thread is for questions that are typically not permitted elsewhere on /r/DIY. Topics can include where you can purchase a product, what a product is called, how to get started on a project, a project recommendation, questions about the design or aesthetics of your project or miscellaneous questions in between.

This is a judgement-free zone. We all had to start somewhere. Be civil.

A new thread gets created every week.

/r/DIY has a Discord channel! Come hang out or use our "help requests" channel. Click here to join!

Click here to view previous Weekly Threads


r/DIY • • Oct 06 '25

weekly thread General Feedback/Getting Started Q&A [Weekly Thread]

15 Upvotes

General Feedback/Getting Started Q&A Thread

This thread is for questions that are typically not permitted elsewhere on /r/DIY. Topics can include where you can purchase a product, what a product is called, how to get started on a project, a project recommendation, questions about the design or aesthetics of your project or miscellaneous questions in between.

This is a judgement-free zone. We all had to start somewhere. Be civil.

A new thread gets created every week.

/r/DIY has a Discord channel! Come hang out or use our "help requests" channel. Click here to join!

Click here to view previous Weekly Threads


r/DIY • • 8h ago

How I dealt with holes in ceiling...

62 Upvotes

I moved a dining table light several inches so it would be centered over a larger table. This left a hole where the old lamp box is. To hire a drywall guy to come in would have cost more than I wanted to pay, but the real pain I wanted to avoid was needing to repaint the entire ceiling, or try to match paint, which almost always fails for me. So I did this:

Large Rectangle Medallion

The medallion covers the hole and looks pretty decent. I got this medallion.

Second issue... I installed two Smart Toilets. Both water lines had to be moved, which involved the plumber cutting two holes in the ceiling on the level under the toilets. These a rough holes that look like crap. I had a drywall guy stop by. He would charge just a tad under $900 to fill the holes and match the texture. He'd be in and out for several days. So I decided to do this:

Cold air return

I bought a couple of cold air return grates and used these neodymium magnets.

First I marked the six holes on the cold air return while it was pressed against the ceiling.. Then I tapped these anchors into the ceiling, and screwed the magnets into the anchors, using the screws that came with the anchors. So the magnets are attached to the ceiling. Then the cold air returns snapped into place with the magnets holding them up. It was important to turn the cold air return grates so the slanted slots hide the hole. The holes are now invisible.

These grates now function as an access panel, and it's really on there solid. It's not falling down. And anyone who notices it will just think it is an air return. A poor man's access panel. I'm not poor, but I am lazy, and this went together very quickly. I hope it helps someone.


r/DIY • • 19h ago

help Spray foam around a tub?

56 Upvotes

Our plumber recently installed a new bathtub and set it in concrete. However, the sides of the bathtub are hollow. Currently I can access these hollow sides from the other side of the wall next to the tub. Would it make sense to put sprayfoam insulation around the outside of the bottom of the tub for better insulation?

I want to do this because I'm hoping that it will retain heat better and we will save water and heat by not refilling the tub during a long bath. I'm hesitant because I've heard so many horror stories about spray foam and moisture. The tub has got to be watertight anyway, though, so maybe it's fine? I'm also a little concerned about the spray foam expanding and damaging things, but plan to do this with the tub full of water and very carefully (if it's a good idea at all).

All my searches just talk about setting tubs in sprayfoam, but our tub is already set in concrete.


r/DIY • • 13h ago

help How to secure a faux-headboard

15 Upvotes

I bought this inexpensive faux-headboard that includes these small brackets that slide between the mattress and box spring. I'm pretty happy with it, but it has popped out in the middle of the night a couple of times now and left marks on the wall behind it. I assume there's any number of good solutions to this, but I'm curious if anyone has any simple solutions for keeping these brackets in place so I don't damage my landlady's walls any further? I feel like a zip tie or duct tape-level solution should probably exist but I haven't thought of it yet.


r/DIY • • 1h ago

help what do you guys use to keep mosquitoes out of your house?

1 Upvotes

i swear mosquitoes somehow manage to get inside even when i feel like all the windows and doors are closed. it's so annoying when you're about to sleep and suddenly hear that buzzing near your ear, then spend the next few minutes trying to hunt the little thing down lol.

i've tried the usual stuff, but i'm curious if there's anything that actually works long-term. do you guys use mosquito traps, repellents, screens or anything else at home that you'd genuinely recommend?


r/DIY • • 13h ago

help How to fix broken spot in fiberglass tub?

8 Upvotes

The fiberglass is broken in the lower outside corner, right near the drain, so water tends to pool there if the drain gets slow at all. Also I only take showers now instead of baths to avoid too much leakage through the broken spot. What is the best way to attempt to fix it?


r/DIY • • 14h ago

home improvement Furring Strips & Mounting

8 Upvotes

I’m wanting to mount some floating desks in the basement, I have 2x2 furring 16 inches apart, that are directly mounted to the concrete. The basement I believe was poured in 1950.

Are 2x2 ok to use as the floating desk mount? Or do I drill through wood into the concrete and use fasteners through the furring and into the concrete? Would this crush the drywall?

Not planning on anything heavy on the desks maybe one monitor and a printer?


r/DIY • • 1d ago

help Cheap Shower Surround Cracked. Can't afford to replace it.

28 Upvotes

My shower is made up of plastic pieces that fit together. Is it fiberglass maybe? I'm not sure how to tell. Anyway, one of the seams seems to have come loose and now when a little bit of pressure is put on that area, the crack opens by about a 1/2 inch all the way from the top to the beginning of the tub. Can I glue this somehow? I was told to try something called J. B. Weld?

I tried caulk but that did not hold up!

Please help, the crack is so big I can see the 2 by 4's behind the shower when I push on it!


r/DIY • • 12h ago

other Converting kegerator to a (still) water tap.

2 Upvotes

Hi - we rarely use our kegerator anymore so we are thinking of running a line from the sink to the keg. It will be still water, never carbonated. It would of course go under/through the counter & cabinets. What would he a good water filter system that would help us here? We hate using our fridge for water.

We will still use one tap for beer or cold brew so we need to leave room (it holds 2 pony kegs). We would like a filter that is good quality, good taste (thinks Starbucks water), don’t want to spend a fortune.

Almost all searches are coming back for sparkling water which we do not want.

Chatgpt thinks tankless options may not work due to the fact that many tankless options use a smart faucet?

Has anyone done this?


r/DIY • • 22h ago

electronic Tv mount on metal studs

12 Upvotes

I’d like to use a full motion mount on my wall with steel studs. I can’t seem to find any full motion mounts that are either a) rated for steel studs, or b) aren’t limited in their range of motion.

Is it just the type of fasteners that matter? I obviously don’t want to fuck up my wall, but I don’t understand why it really matters.

I also have 3 steel studs that the mount can anchor to. Does that help?


r/DIY • • 21h ago

help Replacement saw blade wrenches?

6 Upvotes

I have a nice Grizzly table saw, but the blade wrenches that came with it are cheap. I've limped along with them for years, but they're finally so sprung that I can't reliably use them anymore.

I've looked around online, and I'm not sure what to replace them with. Something like the originals but in a harder steel would be ideal.

Any suggestions?


r/DIY • • 19h ago

Stuck with hanging door

3 Upvotes

I have hung two doors life time. In both cases the hinges bind like crazy - and they won’t fully close all the way, and especially the lower hinge starts to pull off the jamb. Tried putting cardboard behind the hinges, etc. can’t figure it out. Help! Tried to take a video but don’t seem able to


r/DIY • • 22h ago

electronic Danby Dishwasher 18 inch DDW1899BLS repair tip

5 Upvotes

We've had this dishwasher about 15 years. A fem months ago it started to smell like burning plastic when it ran.

The door that opens and releases the detergent started to be intermittant. Timer function became intermittant.

Solution: I took it apart and found that the power switch had cooked. It was falling apart. I removed the power switch and connected the spade connector wires using a 2 into 1 spade adapter that connected the wires without cutting off the spade connector. I could have just connected the wires together with a butt connector. At the same time I mangled the timer button switch with a pair of pliers. In retrospect I probably should have finished the power switch repair and then tested it. Oh well, timer switch is destroyed. Destroying the timer switch fixed the problem I had with it so all is well.

So now I have no power switch. I now have the Dishwasher plugged into a power strip with a switch. I use the switch to turn it on to run the wash cycle, then I turn if off. Works fine.

At the same time as I did this repair, the top rack failed. It had corroded and the supports failed. The top rack has two positions, upper and lower. I switched it to the other position (in my case, lower) and continued to use it. The top rack is not available from parts suppliers.

TLDR: On this pretty good Danby Dishwashwer the power switch seems to be a weak spot. It failed after 15 years. I removed it and connected the wires so it is always on and now use a Plug strip with a switch to turn on power.


r/DIY • • 1d ago

help ADT removal step by step

7 Upvotes

I’ve been reading up on this but I’m nervous to do this myself. Can I get a review of this plan and any feedback especially when it comes to the electrical safety of it all?
I have a Simon ADT wall unit in my kitchen - there’s wires running from inside the wall to the back of it. No transformer plugged into any visible outlet. No base unit that I can find. No screen display, my sense is it’s off- no visible lights or sounds, but I really don’t know. There’s wires going to it so I want to be careful.

  1. Turn off all the breakers in my house
  2. Unscrew wires from panel
  3. Unscrew panel from wall
  4. Turn on breakers
  5. Klein tool test the wires - if dead, push in wall and patch over. If live - wire nut and push in wall.
  6. Repeat for smaller panel by front door
    Thank you for helping, I’d rather do the drywall part 100 times than mess with the electrical part, but I want to keep learning new homeowner skills.

r/DIY • • 18h ago

help Glue for Shock Cord that is not epoxy

2 Upvotes

I have lots of shock cord and I made all sorts of bands and straps.

The problem is if I use epoxy to glue on the plastic ends/toggles the poxy usually only gets used a little and then the rest of the epoxy goes dry and is a waste. What's the best strong glue you would use that is easily storable?


r/DIY • • 1d ago

help I would like to build a DIY doghouse for my Labrador that will keep it comfortable and warm while it spends time outdoors during the day in Japan—where temperatures can drop to between -6°C and -8°C (roughly from 10:00 AM to 5:00 PM).I have a wide range of tools available, but I lack knowledge rega

52 Upvotes

I have a one-year-old Labrador, weighing 30–35 kg and standing about 80–90 cm tall. Due to the nature of my restaurant business, the dog must be kept outdoors.

I plan to build a shelter with overall dimensions of approximately 80 cm (width) x 90 cm (depth) x 90 cm (height), with an entrance measuring about 60 cm (height) x 50 cm (width).

I also intend to raise the base about 5 cm off the ground.

It will be placed on a wooden deck, and since there is a roof overhead, snow is not a major concern.

I plan to use plywood for the construction, but I have no idea how to go about building the framework or other structural elements.


r/DIY • • 1d ago

outdoor DIY concrete/cement pots curing time?

17 Upvotes

I’m making some outdoor plant pots out of a sand/cement premix and they’ll end up being about 29cm (11.5 in) diameter, 25cm (10in) depth and a wall thickness of just over 2cm (0.8in) How long do I need to let them cure (once removed from the mould) before I seal (inside) and paint (outside)? I’m planning to use a water-based sealant spray that is specifically for exterior use, and then just spray paint them - I’ve been using Dulux duramax and Rustoleum 2X ultra cover spray paints for store bought pots. I’m in Australia and we’re currently experiencing temperatures in the 20-30 degrees Celsius (68-86 Fahrenheit) range and the humidity % is forecasted to fluctuate between low 40s to low 80s in the near future. Thank you!


r/DIY • • 2d ago

home improvement Shower Drain Backing Up When Toilet Paper in Pipe Connection

69 Upvotes

Hi I live in a new build house bought a year and a half ago and I live there alone about one weekend a month. Been going there more often last 3 months to permanently be there and shower drain has backed up in every month the last 3 months. Each time it happens I submit warranty claim , then they say call builder's plumber, and the plumber uses a machine to clear it. But this last time we all looked at camera before clearing it. Toilet paper clump is catching corner/connection of pipes.

Facts: Toilet tank 1.28 gallons. I never double flush. I don't use much water since I'm not here all the time. 2 toilets in the house. Major city in Texas suburb. Two year structural/piping warranty will end this spring.

Questions: Should this be happening or not and is it worth more investigation? The camera showed water was flowing fine until we got to the blockage. And plumber showed me a -1 slope number on the camera is good. But then I saw a bunch of 0,+1, +2. Was that accurate and is that a problem? Warranty guy says use thinner paper double flush and flush often.


r/DIY • • 1d ago

woodworking What should I put under plastic garage tiles?

5 Upvotes

I have a workshop and I am putting in plastic garage tiles for the floor. What if anything, should I put under the tiles to prevent them from moving or lessen noise. The floor in the workshop is concrete.


r/DIY • • 1d ago

help Repairing PRV and replacing thermal expansion tank, both at the same time or can I do the expansion tank now?

8 Upvotes

I am going to be cleaning/repairing my pressure reducing valve (PRV)and replacing my thermal expansion tank (TET) what is the correct order of operation? My understanding is that I should get the pressure reducing valve taken care of, get it set where it needs to be, adjust the new Thermal expansion tank to match the pressure I set and then install it. Or should I get the TET replaced now?

My PRV (Zurn NR3XL) is having issues. The pressure will initially be at about 60psi then slowly creep up to about 70psi. Then if I run a faucet it drops to about 40psi before slowly climbing back up to 70psi. I have a repair kit in the mail, just in case when I open it up there is a damaged part that needs replacing, I was stoked to learn there is a cleaning/repair options and I don't need to replace the whole thing. My TET also seems shot, when I checked it it seemed to have no pressure in it and if I tried to add pressure it would not take any until I managed to get the PSI on the pump over 100psi. There was pop and a drop at the pump and I could then pump air into it.

 

*Update 11-21-2026

This morning I turned off the line into the water heater to see what the line pressure would do. while running the pressure drops to 40psi. when it is off it jumps to 80psi. The same behavior is observed with the line to the hot water being on. The repair kit for the PRV will not arrive until 11-30, and I would prefer to wait until that arrives to clean the internals of it in case something does need to be replaces. I also removed the TET and confirmed it is shot. detached it would not hold air, just vented out of the opening for the water, and it had some nice brown water sitting in it.

What I decided to do is, with a tap running I adjusted the PRV to set a dynamic/flowing pressure of 60psi. I then decided to set the new TET between the dynamic and static pressure (70psi). Please feel free to yell at me if this is a boneheaded idea and correct what I should do. After attaching the new TET the pressure fluctuation are the same, 60psi dynamic and about 80psi static. Once I get the repair kit I will address the PRV, depressurize the water heater, and readjust the TET.


r/DIY • • 2d ago

help How good is the store bought sanded caulk?

9 Upvotes

Im still on my first cup of coffee. So please ignore any typos haha.

I'm slowly chipping away at renovating my house. I did my shower walls with grout since I wasn't sure about the sanded caulk. Im ok with miatnancing grout but if there's a better more maitnance free option. I'd like to replace the caulk in the corners where tile meets with the sanded caulk and maybe instead of grout for my tile floor use it instead. Im very much on the fence though. There's got to be a reason you dont often see it used. I know making your own is a recipe for disaster.


r/DIY • • 2d ago

Need to make an affordable fake window

71 Upvotes

I rent a 1 bedroom basement, i have a small window in my bedroom but nothing in the living room and it kills my energy. Any ideas on how to get this done under $100?


r/DIY • • 3d ago

help Quick cheap way to make mattress frame? Just need to get my mattress off the floor for now

92 Upvotes

My budget is 100$ Im trying to figure out a cheap way to make a quick bedframe. I have two twin mattresses i want to put together side by side to make more mattress space.

I was originally thinking cinder blocks and wood boards, but everyone on here says dont use cinder blocks inside. I dont really care if they crumble. I just want my mattress off the floor until I have enough money to buy a bigger mattress and actual bed frame