r/DIY • • 18h ago

help Spray foam around a tub?

53 Upvotes

Our plumber recently installed a new bathtub and set it in concrete. However, the sides of the bathtub are hollow. Currently I can access these hollow sides from the other side of the wall next to the tub. Would it make sense to put sprayfoam insulation around the outside of the bottom of the tub for better insulation?

I want to do this because I'm hoping that it will retain heat better and we will save water and heat by not refilling the tub during a long bath. I'm hesitant because I've heard so many horror stories about spray foam and moisture. The tub has got to be watertight anyway, though, so maybe it's fine? I'm also a little concerned about the spray foam expanding and damaging things, but plan to do this with the tub full of water and very carefully (if it's a good idea at all).

All my searches just talk about setting tubs in sprayfoam, but our tub is already set in concrete.


r/DIY • • 6h ago

How I dealt with holes in ceiling...

48 Upvotes

I moved a dining table light several inches so it would be centered over a larger table. This left a hole where the old lamp box is. To hire a drywall guy to come in would have cost more than I wanted to pay, but the real pain I wanted to avoid was needing to repaint the entire ceiling, or try to match paint, which almost always fails for me. So I did this:

Large Rectangle Medallion

The medallion covers the hole and looks pretty decent. I got this medallion.

Second issue... I installed two Smart Toilets. Both water lines had to be moved, which involved the plumber cutting two holes in the ceiling on the level under the toilets. These a rough holes that look like crap. I had a drywall guy stop by. He would charge just a tad under $900 to fill the holes and match the texture. He'd be in and out for several days. So I decided to do this:

Cold air return

I bought a couple of cold air return grates and used these neodymium magnets.

First I marked the six holes on the cold air return while it was pressed against the ceiling.. Then I tapped these anchors into the ceiling, and screwed the magnets into the anchors, using the screws that came with the anchors. So the magnets are attached to the ceiling. Then the cold air returns snapped into place with the magnets holding them up. It was important to turn the cold air return grates so the slanted slots hide the hole. The holes are now invisible.

These grates now function as an access panel, and it's really on there solid. It's not falling down. And anyone who notices it will just think it is an air return. A poor man's access panel. I'm not poor, but I am lazy, and this went together very quickly. I hope it helps someone.


r/DIY • • 22h ago

help Cheap Shower Surround Cracked. Can't afford to replace it.

27 Upvotes

My shower is made up of plastic pieces that fit together. Is it fiberglass maybe? I'm not sure how to tell. Anyway, one of the seams seems to have come loose and now when a little bit of pressure is put on that area, the crack opens by about a 1/2 inch all the way from the top to the beginning of the tub. Can I glue this somehow? I was told to try something called J. B. Weld?

I tried caulk but that did not hold up!

Please help, the crack is so big I can see the 2 by 4's behind the shower when I push on it!


r/DIY • • 12h ago

help How to secure a faux-headboard

12 Upvotes

I bought this inexpensive faux-headboard that includes these small brackets that slide between the mattress and box spring. I'm pretty happy with it, but it has popped out in the middle of the night a couple of times now and left marks on the wall behind it. I assume there's any number of good solutions to this, but I'm curious if anyone has any simple solutions for keeping these brackets in place so I don't damage my landlady's walls any further? I feel like a zip tie or duct tape-level solution should probably exist but I haven't thought of it yet.


r/DIY • • 20h ago

electronic Tv mount on metal studs

11 Upvotes

I’d like to use a full motion mount on my wall with steel studs. I can’t seem to find any full motion mounts that are either a) rated for steel studs, or b) aren’t limited in their range of motion.

Is it just the type of fasteners that matter? I obviously don’t want to fuck up my wall, but I don’t understand why it really matters.

I also have 3 steel studs that the mount can anchor to. Does that help?


r/DIY • • 12h ago

help How to fix broken spot in fiberglass tub?

8 Upvotes

The fiberglass is broken in the lower outside corner, right near the drain, so water tends to pool there if the drain gets slow at all. Also I only take showers now instead of baths to avoid too much leakage through the broken spot. What is the best way to attempt to fix it?


r/DIY • • 12h ago

home improvement Furring Strips & Mounting

8 Upvotes

I’m wanting to mount some floating desks in the basement, I have 2x2 furring 16 inches apart, that are directly mounted to the concrete. The basement I believe was poured in 1950.

Are 2x2 ok to use as the floating desk mount? Or do I drill through wood into the concrete and use fasteners through the furring and into the concrete? Would this crush the drywall?

Not planning on anything heavy on the desks maybe one monitor and a printer?


r/DIY • • 23h ago

help ADT removal step by step

8 Upvotes

I’ve been reading up on this but I’m nervous to do this myself. Can I get a review of this plan and any feedback especially when it comes to the electrical safety of it all?
I have a Simon ADT wall unit in my kitchen - there’s wires running from inside the wall to the back of it. No transformer plugged into any visible outlet. No base unit that I can find. No screen display, my sense is it’s off- no visible lights or sounds, but I really don’t know. There’s wires going to it so I want to be careful.

  1. Turn off all the breakers in my house
  2. Unscrew wires from panel
  3. Unscrew panel from wall
  4. Turn on breakers
  5. Klein tool test the wires - if dead, push in wall and patch over. If live - wire nut and push in wall.
  6. Repeat for smaller panel by front door
    Thank you for helping, I’d rather do the drywall part 100 times than mess with the electrical part, but I want to keep learning new homeowner skills.

r/DIY • • 19h ago

help Replacement saw blade wrenches?

6 Upvotes

I have a nice Grizzly table saw, but the blade wrenches that came with it are cheap. I've limped along with them for years, but they're finally so sprung that I can't reliably use them anymore.

I've looked around online, and I'm not sure what to replace them with. Something like the originals but in a harder steel would be ideal.

Any suggestions?


r/DIY • • 21h ago

electronic Danby Dishwasher 18 inch DDW1899BLS repair tip

5 Upvotes

We've had this dishwasher about 15 years. A fem months ago it started to smell like burning plastic when it ran.

The door that opens and releases the detergent started to be intermittant. Timer function became intermittant.

Solution: I took it apart and found that the power switch had cooked. It was falling apart. I removed the power switch and connected the spade connector wires using a 2 into 1 spade adapter that connected the wires without cutting off the spade connector. I could have just connected the wires together with a butt connector. At the same time I mangled the timer button switch with a pair of pliers. In retrospect I probably should have finished the power switch repair and then tested it. Oh well, timer switch is destroyed. Destroying the timer switch fixed the problem I had with it so all is well.

So now I have no power switch. I now have the Dishwasher plugged into a power strip with a switch. I use the switch to turn it on to run the wash cycle, then I turn if off. Works fine.

At the same time as I did this repair, the top rack failed. It had corroded and the supports failed. The top rack has two positions, upper and lower. I switched it to the other position (in my case, lower) and continued to use it. The top rack is not available from parts suppliers.

TLDR: On this pretty good Danby Dishwashwer the power switch seems to be a weak spot. It failed after 15 years. I removed it and connected the wires so it is always on and now use a Plug strip with a switch to turn on power.


r/DIY • • 17h ago

Stuck with hanging door

3 Upvotes

I have hung two doors life time. In both cases the hinges bind like crazy - and they won’t fully close all the way, and especially the lower hinge starts to pull off the jamb. Tried putting cardboard behind the hinges, etc. can’t figure it out. Help! Tried to take a video but don’t seem able to


r/DIY • • 10h ago

other Converting kegerator to a (still) water tap.

2 Upvotes

Hi - we rarely use our kegerator anymore so we are thinking of running a line from the sink to the keg. It will be still water, never carbonated. It would of course go under/through the counter & cabinets. What would he a good water filter system that would help us here? We hate using our fridge for water.

We will still use one tap for beer or cold brew so we need to leave room (it holds 2 pony kegs). We would like a filter that is good quality, good taste (thinks Starbucks water), don’t want to spend a fortune.

Almost all searches are coming back for sparkling water which we do not want.

Chatgpt thinks tankless options may not work due to the fact that many tankless options use a smart faucet?

Has anyone done this?