r/hvacadvice • • Mar 02 '26

General Information About Bans and Rules

0 Upvotes

There has been an uptick on posts and complaints about mods banning. Please be advised, there are rules for the page. No ads (includes promotions for a company), Reddits rules, no crossposting, transparency and safety (this is a big one; we want homeowners to be safe, if you provide unsafe practices or advice (blacklisted items) or tell a user to dm you, the comment will be removed and you may get banned), blacklisted topics (basically topics that homeowners should not be fixing themselves, gas, some high voltage), civility, no companies asking for surveys, advertisements or general questions, and no market research or ai/SaaS.

Posts complaining about this are not allowed either. We are all reasonable and work in the trade, talk to us through ModMail and we can come to a solution. Complaining or namecalling will usually result in a ban, so be civil.

Remember, we are doing this in our freetime to help homeowners with their units, both the users and mods. The mods in this group are in the trade and have day jobs as all of you do. I've been in this trade for 10 years and still do hvac as my job, just traveling now for a manufacturer. Similar with every mod. It is actually a requirement to be a mod, you have to be in the trade, be approved, have good history in the sub and provide enough time to moderating it.

I thank you for your time and if you have any questions, you can comment on this or send us a mod message. No DM's, we will not answer these. Only ModMail.


r/hvacadvice • • Nov 13 '25

READ THIS I am assuming this is not normal.

177 Upvotes

I was loading the car for work when I saw this. It felt and smelled like steam not smoke. Did I just catch it at the end of the cycle or is there a mechanical problem such as a stuck motor? It was 40° at the time and no rain. Heat was set to 70 and the house was 70.


r/hvacadvice • • 20h ago

Electrical Did I just save $1400+ in 30 minutes?!

210 Upvotes

During a routine seasonal check and tune up of the heat pump, the tech came back saying the defrost control unit needed to be replaced. He gave pictures with the burnt out resistors so it was a reasonable catch from what I could tell. The estimate for the repair was $1500 and I would have to wait a week. At first I signed off because I moved into the house with the unit in disrepair so I am trying my best to be proactive and keep it alive before I have to drop $20k.

Shortly after I did some checking online and at that point had to call in and call it off.

Went on Grainger and 2 days later was repairing the unit myself. After 30 minutes (20 minutes install, 10 minutes double and triple checking the connections since I don't know anything about heat pumps) I was back up and running with a brand new control board. I was out a total of $80 ( unit, taxes and shipping).

I know the companies are mostly about selling $20k units, but if you keep taking $1500 from me every time you come out, how am I ever going to have enough money saved for that $20k unit when the time comes?

This ain't right. What is going on in the industry?!


r/hvacadvice • • 3h ago

Furnace I had a new high efficiency furnace installed over the summer and I'm starting to use the furnace. What is acceptable CO2 ranges in a house?

Thumbnail
gallery
6 Upvotes

Whenever my furnace gets into that 2nd stage or works harder, I get high levels of Carbon Dioxide in my house. The only real standard is OSHA for a work place at 5000ppm avg over 8 hours. Most studies seems to suggest that over 1000ppm will start to make you nauseous and dizzy.

The owner of the company who installed the whole HVAC system keeps citing the 5000ppm and suggesting it fine. I have gotten them to at least reseal the exhaust where it was dripping 2 times and another time right now at another spot.

Is there anything that I can talk to the owner about to prove that over 1000ppm is getting dangerous over extended periods?

Update: they just fixed a part of the exhaust PVC where I think it was leaking. Furnace is running, house has been flushed and co2 levels in the house are under 500ppm.

Edit: Many of also seem to not know the difference between Carbon monoxide and Carbon Dioxide. Please know the difference before responding. Here is an article telling you the difference.


r/hvacadvice • • 8m ago

Doesn’t seem right

Thumbnail
gallery
2 Upvotes

Just asking. 4,320 SQF home. I keep seeing this around the home.


r/hvacadvice • • 1h ago

Furnace How do I lower my new-build home humidity?

2 Upvotes

Bought a new place (first-time home buyer) and my humidity is reading upwards of 56%. I’m located in Alberta, Canada, and outside temperatures are currently at -7 low and -4 high Celsius. I have an HRV and, as far as I can tell, no humidifier installed on furnace (but I could be wrong). How do I go about lowering humidity since there’s no humidity control on the thermostat?


r/hvacadvice • • 2h ago

Boiler in Rental

Thumbnail
gallery
2 Upvotes

My landlord says this was recently inspected but he is not trustworthy. It works but the previous tenant said the place was real expensive to heat.


r/hvacadvice • • 1d ago

General Roof leak. Roofers covered by flue with a tarp. Am I gonna die if I run my heater or is this ok?

Post image
125 Upvotes

r/hvacadvice • • 15m ago

Electrical Ecoforest Gateway Modbus Connector

Post image
1 Upvotes

Hello,
I would like to connect to my heat pump using Modbus (and home assistant). My unit has the Ecoforest gateway (which I’m not using). It looks like the unused connector on the gateway is meant to add to the MOD bus chain.

Does anyone know if this is the case and what is the connector type for this?


r/hvacadvice • • 42m ago

Is this insulation done for?

Thumbnail
gallery
1 Upvotes

Hi, r/hvacadvice. I decided today that I’d take off and clean my room’s ceiling supply register since there’s mold apparent on the fins. After removing the register itself I saw that the insulation surrounding the interface (not sure of the technical word here) looks…worse for wear. I’d appreciate some expert opinions on what I am or am not dealing with here.
For what it’s worth, all the ducts are brand new- less than a year old. The previous ductwork was around for the better part of 30 years or so.


r/hvacadvice • • 55m ago

Furnace Strange wire on furnace filter?

Thumbnail
gallery
1 Upvotes

I feel completely out of my element here. We are renting and were told to clean the furnace filter. Upon looking closely, we noticed this wire. Is it frayed? Is it supposed to be like this? It’s made by Sears which no longer exists. The filter/casing appears to be the type that is electrified. We’re worried about this wire and the mesh appearing to be damaged. Any advice would be greatly appreciated as our landlord does not appear to know…


r/hvacadvice • • 1h ago

Likely a dumb question but if your gas furnace is currently not operating, is it okay, until it is fixed, to use your heat pump?

Post image
0 Upvotes

I don't know exactly if my friend's heat pump is wired independently of the gas furnace but this is a photo of it.


r/hvacadvice • • 1h ago

Would you run a 4x10 to 6" end boot with reducer that is oriented for a window or turn it 90 degrees without a reducer?

Thumbnail
gallery
1 Upvotes

I can't find these end boots for 5" duct. I want this style boot (first photo) so that the long side is along the window. But this means I need to use a 6 to 5" reducer. Or should I go with the 5" box that will be turned 90 so the short end is along the window?


r/hvacadvice • • 1h ago

Trying to move dishwasher location but there's ductwork. What do i do?

Thumbnail
gallery
1 Upvotes

My more diy savvy family members have said 1, move it, or 2, delete and block it off if the other register is also blowing (as in not return... idk the proper term).

I'd like to move it to the next cabinet kickplate over, the one closer to the sink/ existing dishwasher space, but as you can see from the basement photo, plumbing is right there. Plus I'd have to run it back and delete at the source, cut and rerun, right?

Let me know your thoughts. Thanks!


r/hvacadvice • • 6h ago

Career Jump Advice

2 Upvotes

I want out of the car dealership life ….im 40 and got in at 18 …I was a technician for some time ….I understand cars just not houses ….i understand vehicle HVAC but not houses albeit they share identical Principals….i got out from being a tech and now im the guy behind the counter writing up
Tickets and repair orders and dispatch to tech to work on vehicle (service advisor) i want to get back in the hands on world at 40…I still build cars on the side and race them (HONDA FOR LIFE lol) …. Im interested in HVAC…. Is it too late for me or am I too old to jump
Ship and transition into unknown territory?


r/hvacadvice • • 2h ago

Lennox G30 (draught diverter)

Post image
1 Upvotes

Lennox G30 furnace – should the end of this flue box be open?

I have a Lennox G30 gas warm-air furnace, It’s around 50 years old, every since we moved in I’ve noticed a slight smell of gas / fumes when the pilot light is on but the furnace is not running (we have a monoxide alarm next to it, which has NOT trigged).

On top of the furnace is a rectangular metal box connected to the flue. One end is capped and the other is open, when i look inside i can see the flue is open to this box. The flue is over 10 metres long, with a fan at the far end to draw the exhaust out.

I covered the open end with foil tape, the furnace still runs fine and the smell is now less noticeable.

What i've read is the that this end is meant to be open therefore should I remove the tape ?


r/hvacadvice • • 2h ago

General Flame roll out switch keeps tripping

1 Upvotes

The flame is definitely rolling out. Issue just started happening. Maybe a cracked heat exchanger or is my chimney plugged?


r/hvacadvice • • 2h ago

Best way to tackle fresh air intake issue?

1 Upvotes

So a month ago we replaced our old single stage 3 ton carrier system. We with with a Carrier Greenspeed. We are out of Central Florida area, so we have a hot humid climate.

It's installed in a closet inside the house with a louvered door for the return. There is a 6" duct inside the closet which goes into the attic and splits into 2 4" ducts near the soffit, going into soffit vents.

So my concern is after getting a CO2 monitor, I have 3000+ inside my house regularly. Because it runs in low CFM most of the time, while the damper opens (using a pressure switch to tell if the blower is on), it seems like there is not enough negative pressure in that closet for it to draw fresh air in.

So my question is, what's the best way to handle this? Just put a fan on the duct there so when the damper opens, the fan kicks on too and I forcefully pull say 90cfm into the closet? If I do that, put the fan in the attic so I don't have the extra noise, as when the AHU is running low, I can't hear it running with the door shut)? Do I add a NIM with Carrier so I can have a controller on when it opens and closes without using a third party controller? Do I find/add a cheap ERV? It's close to the garage so I could probably install it close to the ladder which is close to the AHU. The G terminal is used for the float switch already, so I can't have a blower tie into the carrier to tell it to turn the blower on (and there is only a humidifier output in the AHU which I can't use for this). Also, if I do an ERV, power and wiring is easy, from what I read, ERV's should not need a drain, so if I did one, I would want one that would not require that.


r/hvacadvice • • 2h ago

Advice on replacements

1 Upvotes

My furnace blower motor is going out. I knew it was old, but come to find out, furnace is 30 years old. 2 separate companies have quoted 4k and 6k each to replace the furnace. My a/c unit is also 13 years old. The 4k company is asking for 10k total to do a full system replacement, and strongly recommending both be replaced. Are these numbers worth it and would it be wise to replace furnace only, or should I just bite the bullet on a whole system? I'm in central texas. Thanks in advance.


r/hvacadvice • • 2h ago

Water Heater Did my servicers forget to reinstall my humidifier?

Post image
0 Upvotes

We had a whole-home humidifier installed last year. This year we had our whole furnace and AC replaced by the same company (it was 16+ years old and busted).

Now that it's getting colder, we've noticed an intermittent sewer smell from the utility closet. It is 100% not a gas smell, it's sewer. Like a dried out drain.

I took a look and realized "wait, where's the big plastic tube thing?" The big plastic tube thing is what I remember the humidifier looking like. I also noticed this open joint with nothing connected to it. Is that where my humidifier was connected? Did they forget to reinstall it? Does that explain the sewer smell?

I just emailed my service company but wanted to check here whether my layman theory is plausible at all.


r/hvacadvice • • 3h ago

AC Questions on insulating and supporting existing hvac ducting in crawlspace

1 Upvotes

https://imgur.com/a/ayyIoEG

These ducts had yellow insulation but no metal outside and were in pretty poor shape with a ton of spots where the insulation was damaged or destroyed. I had a full respirator and bunny suit and removed all the old insulation. I'm sure a lot of the dirty spots on the insulation was from air leaks.

I'm trying to figure out the correct order to get this all back together.

  1. Seal all the joints with mastic tape
  2. Insulate
  3. Fix strapping / supports

I don't know if it makes sense to remove the ducts in order to add insulation or not. I'm leaning toward NO since they're already suspended and there's (barely) enough room to work. The ducts seem to be in decent enough condition? There's a few rust spots but nothing more than superficial. The main benefit would be that it'll make it easier to get to the exterior wall to attach the vapor barrier, but I think I can manage without.

Before adding mastic, should I shore up the strapping so that the ducts are aligned properly? Looking at the last pictures, there's a 12" diameter duct with a few swivel elbows that seems to be on the ground when it shouldn't be. I'm pretty sure I can just rotate this back up since there is a swivel on each side and suspend it rather than have it on the ground. Do all this before adding mastic anywhere.

For suspending the ducts - there are currently using wire on nails. This seems like a pinch point. I do like that the wire could be adjusted after the fact, but I feel like you'd need some sheet metal or something to distribute the load so it doesn't cut into the insulation. This may also be the case for flat strapping though right? I'm trying to see what gauge metal to use if I switch to strapping, screws vs nails, and all that.

I've been watching this guy on YouTube (AGL Mechanical Tips - side note, this guy is a fuckin G for having these quality videos for free) https://www.youtube.com/watch?v=PQYboi8eC-s but trying to figure out how to get some of these more oddly shaped wye connectors wrapped while in the crawlspace.

I'm having trouble finding larger rolls of insulation. I'll check some local supply stores and see if they'll sell to a homeowner.

The last option would be to just hire someone to do all this. I'll probably get a quote on Monday if possible, but how that I have the drainage matting down, it's not so bad working in there.

Any tips or advice here?

The run is

  • 12"
  • takeoff
  • 10"
  • wye
  • 7"

r/hvacadvice • • 3h ago

Furnace Normal Furnace Vent Pipe Sound?

0 Upvotes

Good Morning Everyone,
| (24f) just purchased my first home and I'm learning everything there is about HVAC Maintenance. The heater is currently on and outside the vent pipe makes this sound. The HVAC was installed in September of this year. Probably a dumb question but thought l'd ask.


r/hvacadvice • • 4h ago

General Is it worth it trying to fix this, 18 year wall heater has gas leak on burner tubing.

Thumbnail
gallery
1 Upvotes

[Wall heater model W505F-D, 2008]Just had PG&E come to turn on the pilot light for us as it’s getting cold. 3rd year in this house to do it. However, tech told me pilot light burner tubing was leaking gas. Suggested I can find the part and do on my own if I want to. Usually I feel confident to do so but I couldn’t find any videos how to so I decided to get a second opinion. Even though I stated the issue, I paid a tech from a company (horrible experience overall), that not recommended to just replace one part because it’s old. I don’t want to mess up because it’s gas and just want to know if it is possible to just replace that tubing and be ok for another winter cuz I can’t afford a brand new wall heater right now…


r/hvacadvice • • 4h ago

dumb question, pls help

Thumbnail
gallery
1 Upvotes

EDIT- i got the filter out! thanks everyone. just need a ruler and to not be scared i was breaking it lol. BUT the filter i measured the inside where the filter sits and it measures 18×17¾ and the thickness is just BARELY over an inch. there are no pre filters for this so do i have to get another of the shitty green ones so i can custom cut it?

i am so confused on replacing my filter. is this green stuff my filter? i’ve been trying to go back and forth with chat (i know, i know) and i found it semi helpful but now im doubting it all. i cant pull it out, it only comes out like an inch and it gets stuck and it started to tear a tiny bit so i put it back. i just moved to this house and started using the heat and ive just never seen a filter like this before